Status codes and detail codes for Receive processing

Ended successfully.

Failed to allocate the Receive file. For detail codes, refer to the return codes for the DYNALLOC macro in Authorized Assembler Services Guide.

An error occurred during transfer processing.

An error occurred during receiving.

Failed to release the connection with the communication destination.

An error occurred during receiving.

* The message 'XRR0005' appears on the console. For details on error codes, check the RC=xxxx of the console message, and then refer to the applicable section in Communication error code list.

Failed to access the management file. For detail codes, refer to the feedback codes in DFSMS Macro Instructions for Data Sets.

An error occurred on the host on the sending side. Refer to Detail codes when errors occur on sending-side hosts.

The applicable file ID is in use by the Receive processing.

The region for the Receive program (XRRCV) is insufficient.

A communication protocol error has occurred in HULFT.

The version of HULFT on the host on the sending side does not match.

The specified File ID is not registered in the Receive Management Information.

Failed to allocate the Receive file.

Failed to open the Receive file.

Failed to output the Receive file.

Dynamic replacement with message failed.

The contents of the Receive Management Information are inappropriate.

Cancelation or forced termination processing was carried out.

Startup of the Post-receive Job ended in time-out.

The Post-receive Job ended unsuccessfully.

The Post-receive Job is complete, but ended with a status code error.

Job execution of the next job has failed.

The member of the Post-receive Job does not exist.

Multi is specified for the Multivolume.

The Receive file has been specified as a generation file.

Append is specified for the Registration Mode.

Multiple Receive is specified for the Receive Mode.

The Print Character is specified.

The type of the unit that is specified for the UNIT is tape media (MT).

Failed to access the intermediate volume.

The message 'XRRFS06' appears on the console, and the detail code is output. Look up the detail code.

An error occurred during the check of the Transfer Group Information ID.

An error occurred during the check of the name of the host on the sending side.

This is a Record Count error for the host on the sending side and the host on the receiving side.

This is a Record Size error for the host on the sending side and the host on the receiving side.

Dynamic change of the Send file name failed.

The length of the receive file name for instant transfer exceeds 44 bytes.

Correctly specify the receive file name.

The length of the receive volume name (RCVLOC) for instant transfer exceeds 6 bytes.

Correctly specify the receive volume name (RCVLOC).

An error occurred during the INFLATEINIT processing.

Contact your Technical Support Service representative.

An error occurred during the INFLATE processing. There may be an error in the Cipher Key.

Check if the Cipher Key is correct. If you cannot resolve the problem, contact your Technical Support Service representative.

Failed to convert between EBCDIC codes.

Failed to convert custom characters.

A user table cannot be specified for code conversion from UTF-8.

Code conversion from UTF-8 is not possible.

The volume serial number for the Receive file is unknown.

Encryption processing failed.

An error occurred on the host on the sending side after the Successful Job ended. Refer to Detail codes when errors occur on sending-side hosts.

An error occurred during transfer after the Successful Job ended.

An error occurred during receiving after the Successful Job ended.

The transfer type is not supported for receiving with RDW.

The record format of the Receive file is not supported for receiving with RDW.

An error occurred during receiving with RDW. Check the settings and data on the host on the sending side.

Attempted the Receive processing for a multi-volume file, but 'Restore' is specified for the Error Handling in the Receive Management Information. Either specify a single-volume Receive file, or change the Error Handling in the Receive Management Information.

An error occurred in the z/OS Unicode Services during code conversion.

This is a HULFT system error. "XRC0010" is displayed on the console.

If you have a technical support agreement, check the return code and the reason code displayed in the error message and then contact your Technical Support Service representative.

The host on the sending side does not support the Transfer Test function.

Failed to wait for the socket-closed notification from the host on the sending side.

* The network may have disconnected. Error handling or the Unsuccessful Job is not executed, but the log record of unsuccessful end remains on the host on the receiving side. Processing on the host on the sending side may have ended successfully. Check the environments on both sides.

A function that cannot be used with the version of HULFT at the communication destination is specified.

• XML transfer is specified on the host on the sending side

A request that is not supported was accepted. This occurs when a request such as the Send Request is issued to the Receive program (XRRCV).

Confirm that the combination of the code set of the remote host that is specified for the Code Set for Transfer (KCODETYPE) in the Host Information and the code set that is specified for the Code Set for Transfer (CS4TRNSFR) in the System Environment Settings is supported.

For details, refer to the explanation on Convertible Code Set Combinations in Code Conversion Manual.

Confirm that the combination of the code set specified for the Code Set for Transfer (KCODETYPE) in the Host Information and the setting of the EBCDIC Set in the Send Management Information or the Receive Management Information is supported.

For details, refer to the explanation on Convertible Code Set Combinations in Code Conversion Manual.

Failed to communicate in Forced Strong Key mode. Confirm that the communication destination meets all of the following conditions:

1. The Forced Strong Key mode is enabled.

2. The version of HULFT is V8.4.0 or higher.

3. HULFT Cipher Option (AES) Ver.8.0.0 or higher is installed.

The length of the cipher key in the management information is not correct. If the Forced Strong Key mode is enabled, specify a hexadecimal character string of 64 bytes for the cipher key.

If the Forced Strong Key mode is disabled, specify an alphanumeric character string of 0 bytes or an alphanumeric character string of 8 to 20 bytes for the cipher key.

An Instant Transfer request from the sending-side host was refused.

Check if the request from the sending-side host is correct. If it is correct, take one of the following measures:

1. If the information of the sending-side host is not registered in the Host Information, register the information.

2. If the information of the sending-side host is already registered in the Host Information, modify the setting that allows accepting Instant Transfer requests in the Host Information.

3. Register the prefix of the receive file name in the list of receive file names that are allowed in instant transfer.

4. In the list of receive volumes that are allowed in instant transfer, register the volume that is specified for the location on the receiving-side host.