Send File command (utlsend.exe)
21 Parameter error(%d).
- Description:
-
A parameter error occurred.
- Measure:
-
Specify a numeric value from 1 to 256 for Transfer Priority.
22 Parameter error(%d).
- Description:
-
A parameter error occurred.
- Measure:
-
Specify a numeric value from 1 to 256 for Transfer Priority.
23 Parameter error(%d).
- Description:
-
A parameter error occurred.
- Measure:
-
Specify a Send file name within 200 bytes.
24 System error(%d).
- Description:
-
A system error occurred.
- Measure:
-
Check the TCP/IP settings. After checking the TCP/IP settings, check whether communication with the remote host is possible.
28 System error(%d).
- Description:
-
A system error occurred.
- Measure:
-
Invalid parameter has been set. Specify a correct parameter.
29 No information(%d).
- Description:
-
The Send Management Information has not been registered.
- Measure:
-
Register the file ID specified with the parameter in the Send Management Information.
30 Security error(%d).
- Description:
-
You do not have access to the Send Management Information file.
- Measure:
-
Check access permissions on the Send Management Information file (hulsnddb.dat).
31 No information(%d).
- Description:
-
The Send Management Information has not been registered.
- Measure:
-
Register the file ID specified with the parameter in the Send Management Information.
32 Access denied(%d).
- Description:
-
Reading the Send Management Information failed.
- Measure:
-
The Send Management Information file may be corrupted. Check this by referring to the Send Management
Information in the Management Console screen. If you cannot refer to the information, the Send Management Information file is corrupted. Back up the Send Management Information file, and register the Send Management Information again.
33 No information(%d).
- Description:
-
There is no relevant information in the Transfer Group Information.
- Measure:
-
In the Transfer Group Information, register the information of the transfer group ID that is registered in the Send Management Information.
34 Security error(%d).
- Description:
-
You do not have access to the Transfer Group Information file.
- Measure:
-
Check the access permissions for the Transfer Group Information file (hulrhtdb.dat).
35 No information(%d).
- Description:
-
There is no Transfer Group Information.
- Measure:
-
In the Transfer Group Information, register the information of the transfer group ID that is registered in the Send Management Information.
36 Access denied(%d).
- Description:
-
Reading the Transfer Group Information failed.
- Measure:
-
The Transfer Group Information file may be corrupted. Check this by referring to the Transfer Group Information in Management Console. If you cannot refer to the information, the Transfer Group Information file is corrupted. Back up the Transfer Group Information file, and register the Transfer Group Information again.
37 No information(%d).
- Description:
-
There is no information for the remote host in the Host Information.
- Measure:
-
Register the information for the remote host in the Host Information.
38 Security error(%d).
- Description:
-
You do not have access to the Host Information file.
- Measure:
-
Check access permissions on the Host Information file (hulhstdb.dat).
39 No information(%d).
- Description:
-
There is no information for the remote host in the Host Information.
- Measure:
-
Register the information for the remote host in the Host Information.
40 Access denied(%d).
- Description:
-
Reading the Host Information failed.
- Measure:
-
The Host Information file may be corrupted. Check this by referring to the Host Information in Management Console. If you cannot refer to the information, the Host Information file is corrupted. Back up the Host Information file, and register the Host Information again.
41
- Description:
-
The host name has not been entered for Resend File.
- Measure:
-
To resend a file, specify the remote host.
46 Cannot use [-w](%d).
- Description:
-
A time-out value has been specified for an Asynchronous Transfer.
- Measure:
-
"-w" parameter can be specified only for Synchronous Transfers.
47 Cannot use [-file][-t][-h](%d).
- Description:
-
Unable to specify a file name, a transfer group ID, or a host name dynamically.
- Measure:
-
Set the value of Dynamic Parameter Specification as '1' in the System Environment Settings file to enable dynamic specification.
48 Cannot use [-file][-t][-h](%d).
- Description:
-
Unable to specify a file name, a transfer group ID, or a host name dynamically.
- Measure:
-
Set the value of Dynamic Parameter Specification as '1' in the System Environment Settings file to enable dynamic specification.
49 System error(%d).
- Description:
-
A system error occurred.
- Measure:
-
The resource may be insufficient. Check the system resource.
50 System error(%d).
- Description:
-
A system error occurred.
- Measure:
-
The resource may be insufficient. Check the system resource.
52 Cannot require (%d).
- Description:
-
An error occurred in the connection to the process.
- Measure 1:
-
Check whether the Send process has been started.
- Measure 2:
-
Check whether Command Acknowledge Port No. (sddport) is correct.
53 System error(%d).
- Description:
-
A communication error occurred inside HULFT.
- Measure:
-
Check whether the Send process was completed abnormally.
58 Time-out.(%d).
- Description:
-
Time-out occurred.
- Measure 1:
-
Increase the setting of Socket Read Timeout (socktime). The Value of Socket Read Timeout (socktime) or '-w' parameter is used during a synchronous transfer.
- Measure 2:
-
There may be problems in the socket, operating system failure, or the processing speed and the like. Check the HULFT environment.
78 All Send file operation canceled.(%d)
- Description:
-
All transfers in the Synchronous Transfer were canceled.
79 Part Send file operation canceled.(%d)
- Description:
-
Some of the transfers in the Synchronous Transfer were canceled.
80 Instant transfer cannot be performed because Forced Strong Key mode is enabled.(%d)
- Description:
-
Instant transfer cannot be performed because Forced Strong Key mode is enabled.
- Measure:
-
Check the setting of the Forced Strong Key mode (strongkeymode) in the System Environment Settings.
104
- Description:
-
You do not have access to the Send Management Information file.
- Measure:
-
Check access permissions on the Send Management Information file (hulsnddb.dat).
105
- Description:
-
Send Management Information file is not present.
- Measure:
-
Register the Send Management Information.
110 No information(%d).
- Description:
-
The Transfer Group Information does not contain the relevant information.
- Measure:
-
Register the transfer group ID that is specified for the parameter in the Transfer Group Information.
111
- Description:
-
You do not have access to the Transfer Group Information file.
- Measure:
-
Check access permissions on the Transfer Group Information file (hulrhtdb.dat).
114 No information(%d).
- Description:
-
The host that issued the Send Request does not exist in the Transfer Group Information.
- Measure:
-
Add the requesting host to the Transfer Group Information.
115
- Description:
-
There is no relevant information in the Host Information.
- Measure:
-
Register the remote host in the Host Information.
116
- Description:
-
You do not have access to the Host Information file.
- Measure:
-
Check access permissions on the Host Information file (hulhstdb.dat).
120
- Description:
-
You do not have access to the Host Information file.
- Measure:
-
Check access permissions on the Host Information file (hulhstdb.dat).
123
- Description:
-
You do not have access to the Resend Queue file.
- Measure:
-
Check access permissions on the Resend Queue file (sddreqls.dat).
124
- Description:
-
Resend Queue file does not exist.
127 Memory error(%d).
- Description:
-
A memory error occurred.
- Measure:
-
Resource may be insufficient. Check the system resource.
129
- Description:
-
Failed to write to the Resend Queue file.
- Measure:
-
Check available disk space.
130
- Description:
-
There is no relevant information in the Resend Queue file.
- Measure:
-
Relevant information is not present in the Resend Queue file.
133 All Failure(%d).
- Description:
-
All transfers in the Synchronous Transfer failed.
- Measure:
-
Refer to the Send Log.
134 Part Failure(%d).
- Description:
-
Some of the transfers in the Synchronous Transfer failed.
- Measure:
-
Refer to the Send Log.
135
- Description:
-
A request to stop the Send process was issued during a Synchronous Transfer while there were still unsent files. When the Send process is started and the Send processing is resumed, the unsent files are not sent synchronously.
136
- Description:
-
The Send process ended for unknown reasons during a Synchronous Transfer while there were still unsent files. Restart the Send process. When the Send process is started and the Send processing is resumed, the unsent files are not sent synchronously.
137 exec prejob failure.(%d).
- Description:
-
Failure in starting the Pre-send Job.
- Measure 1:
-
Check whether the activated job is present.
- Measure 2:
-
Check the access permissions for the Job Information of Startup Job registered in the Pre-send Job.
- Measure 3:
-
Check the access permissions for Startup Job registered in the Job Information.
138 prejob abnormal end(%d,%d).
- Description:
-
Abnormal termination of the Pre-send Job.
- Measure 1:
-
Check whether the activated job is present.
- Measure 2:
-
Check the access permissions for the Job Information of Startup Job registered in the Pre-send Job.
- Measure 3:
-
Check the access permissions for Startup Job registered in the Job Information.
139 prejob wait time-out(%d).
- Description:
-
The Pre-send Job timed -out.
140 Invalid connect type(%d).
- Description:
-
The value of Connection Type in the Host Information is invalid.
- Measure:
-
Check the value of Connection Type in the Host Information.
141 Cannot get option information(%d).
- Description:
-
Error occurred when reading hulft.sys.
- Measure:
-
Check whether hulft.sys exists and permissions to the file are properly set.
142 Cannot get system information(%d).
- Description:
-
Failed to acquire operating system information.
- Measure:
-
Check the environment for an operating system error.
146 $MSG replace error - file name too long(%d)
- Description:
-
Character overflow occurred while replacing $MSGn or $MSGLn for the Send file name.
- Measure:
-
Specify $MSGn or $MSGLn for the Send file name within the following byte ranges:
- HULFT lower than Ver.6.3.0:
-
50 bytes or less
- HULFT Ver.6.3.0 or higher:
-
200 bytes or less
147 $MSG replace error - transfer group ID too long(%d)
- Description:
-
Character overflow occurred while replacing $MSGn or $MSGLn for Transfer Group ID.
- Measure:
-
Specify $MSGn or $MSGLn for Transfer Group ID within the following byte ranges:
- HULFT lower than Ver.8.0.0:
-
8 bytes or less
- HULFT Ver.8.0.0 or higher:
-
50 bytes or less
148 $MSG replace error - prejob ID too long(%d)
- Description:
-
Character overflow occurred while replacing $MSGn or $MSGLn for Pre-send Job ID.
- Measure:
-
Specify $MSGn or $MSGLn for Pre-send Job ID within the following byte ranges:
- HULFT lower than Ver.8.0.0:
-
8 bytes or less
- HULFT Ver.8.0.0 or higher:
-
50 bytes or less
149 $MSG replace error - startup job too long(%d)
- Description:
-
Character overflow occurred while replacing $MSGn or $MSGLn for Startup Job.
- Measure:
-
Specify $MSGn or $MSGLn for Startup Job within the following byte ranges for each job:
- HULFT lower than Ver.8.0.0:
-
60 bytes or less
- HULFT Ver.8.0.0 or higher:
-
200 bytes or less
153 An error occurred during character code conversion.
- Description:
-
An error occurred during character code conversion.
- Measure:
-
Insufficient memory.
Terminate any unnecessary applications.
156 Failed to open the Command Message file of the command that you ran.
- Description:
-
Failed to open the Command Message file of the command that you ran.
- Measure 1:
-
Check that the file exists.
- Measure 2:
-
Check the access permissions for the file.
179 Wrong Transfer Protocol (%d)
- Description:
-
The Communication Protocol in the Host Information is invalid.
- Measure:
-
Check the value of the Communication Protocol setting in the Host Information.
211 Get Hulenv.cnf Error (%d).
- Description:
-
Reading the System Environment Settings file (hulenv.cnf) failed.
- Measure 1:
-
Check that the System Environment Settings file (hulenv.cnf) exists.
- Measure 2:
-
Check the access permissions for the System Environment Settings file (hulenv.cnf).