Termination status upon unsuccessful termination of command
When a command has terminated successfully, it returns the exit code '0.' When a command has terminated unsuccessfully, it returns an exit code other than '0,' and outputs messages. Refer to the following section when you run a command in a shell script and intend to use the exit status.
1 No information resend log record.
- Description:
-
Relevant information was not found in the Send Control file (sddsendlist.dat).
- Measure:
-
Check the contents of the parameter and re-execute.
2 Cannot exec command.
- Description:
-
Issuance of the request failed.
- Measure:
-
Check the contents of the parameter and re-execute.
3 Cannot kill daemon.
- Description:
-
The daemon could not be ended.
- Measure:
-
Check the contents of the parameter and re-execute.
4 Require time out.
- Description:
-
Timeout occurred.
- Measure:
-
Increase the set value of Utility Timeout (utlwait) in the System Environment Settings or parameter '-w' and re-execute. In the case of Send Request, increase also the value of Socket Read Timeout (socktime) in the System Environment Settings. When you executed Send File, check whether Send daemon has been started correctly or not, and whether time-out has occurred or not in Pre-send Job execution.
5 An memory error. (system error)
- Description:
-
System Error due to memory occurred.
- Measure:
-
Re-execute after ending other applications.
6 Cannot use file Clear/Delete/Lock.
- Description:
-
When multicasting, 'Clear (C),' 'Delete (D),' and 'Lock (L)' cannot be specified for Send File Mode.
- Measure:
-
For multicasting, specify 'Keep (K)' for the Send File Mode. In addition, check that the transfer group with multiple hosts that are being set has not been specified and also check the permissions of the Send file.
7 A signal error.
- Description:
-
Signal operation failed.
- Measure:
-
Check the permission of the user who executed the startup process.
8 Cannot display status.(sddpid.tmp append open error)
- Description:
-
Creation of the file for status display (sddpid.tmp) failed.
- Measure:
-
An access error to the environment file occurred. Check the permissions and the status of the environment variable 'HULPATH', the permission and the status of Work File Generation Path, file status, disk capacity and so on, and then try again.
9 Send daemon is not running.
- Description:
-
Send daemon does not start.
- Measure:
-
Start the Send daemon and re-execute.
10 Cannot write file.
- Description:
-
Writing of the various files failed.
- Measure:
-
Check the permissions and the status of the environment variable 'HULPATH' and Work File Generation Path (tmpdir), file status, and the disk capacity.
11 File ID nothing.
- Description:
-
File ID specified by the parameter of the Send File command (utlsend) does not exist.
- Measure:
-
Register the information of the specified file ID in the Send Management Information, and try again.
12 Group ID nothing.
- Description:
-
Transfer Group ID of the File ID specified by the parameter of the Send File command (utlsend) does not exist.
- Measure:
-
Register the Transfer Group ID information in the Transfer Group Information and then re-execute.
13 Hostname nothing in the group.
- Description:
-
The host name registered in Transfer Group ID does not exist in the Host Information.
- Measure:
-
In the Host Information, register the host name registered in Transfer Group ID, and try again.
14 A system error.
- Description:
-
System error occurred.
- Measure:
-
An access error to the environment file occurred. Check the permissions and the status of HULPATH, Work File Generation Path (tmpdir), and FIFO Path (fifopath), respectively. In addition, if the FIFO file has already been deleted, re-create FIFO file by using parameter '--recover' in the Send Daemon Termination command (utlkillsnd).
15 An error occurred during character code conversion.
- Description:
-
Error occurred during character code conversion.
- Measure:
-
Check that the code set specified for Code Set for Transfer (cs4trnsfr) in the System Environment Settings is correct. Further, check whether the environment variables 'HULPATH' and 'HULEXEP' are set correctly.
17 A queue generation error.
- Description:
-
Queue generation error occurred.
- Measure:
-
The operating system environment is in unstable condition. Restart the Send daemon.
20 Some queue error. (synchronized)
- Description:
-
When multicasting in the Synchronous Transfer, some of sending ended with error.
- Measure:
-
Remove the cause of the problem according to the error code of the Send Log, and retry transfer. Also check HULFT-HUB, if your HULFT is under control of HULFT-HUB.
21 All queue error. (synchronized)
- Description:
-
In the Synchronous Transfer, all of sending ended with error.
- Measure:
-
Remove the cause of the problem according to the error code in the Send Log, and perform the transfer again. In addition, check if your HULFT is being used by HULFT-HUB.
22 All connection PPP. (PPP)
- Description:
-
The Send File is not possible because the hosts of each Send destination are all PPP connected.
- Measure:
-
Check the corresponding host of the Host Information. It is not possible to send from HULFT Ver.7 or higher to the host for which Connection Type (CONNECTTYPE) is PPP connection.
23 Some connection PPP. (PPP)
- Description:
-
The Send File was not possible because some of the hosts of each Send destination were PPP connected.
- Measure:
-
Check the corresponding host of the Host Information. It is not possible to send from HULFT Ver.7 or higher to the host for which Connection Type (CONNECTTYPE) is PPP connection.
24 Hostname nothing.
- Description:
-
The host name registered in Transfer Group ID does not exist in the Host Information.
- Measure:
-
In the Host Information, register the host name registered in Transfer Group ID, and re-execute.
25 Cannot use parm [-file filename][-t hostgroup | -h hostname]
- Description:
-
Dynamic specification of Send File Name, Transfer Group ID, and Host Name is not allowed.
- Measure:
-
Set the value of Dynamic Parameter Specification as '1' in the System Environment Settings file
26 A pre-job execute error.
- Description:
-
The Pre-send Job terminated abnormally.
- Measure:
-
Check the Send Management Information, the Job Information, and the job registered in the Job Information and re-execute.
27 A proxy connect error.
- Description:
-
Connection to HULFT-HUB failed.
- Measure:
-
Check the environment and the Host Information.
28 Some connection SAN(F). not support SAN(F).
- Description:
-
The Send File could not be issued to some Send destination hosts because the connection type of the hosts was a SAN Connection.
- Measure:
-
HULFT-SAN is not installed. Check the corresponding host of the Host Information. It is not possible to send from HULFT to the host for which Connection Type (CONNECTTYPE) is SAN connection.
29 All connection SAN(F). not support SAN(F).
- Description:
-
The Send File cannot be issued because the connection type of all Send destination hosts is a SAN Connection.
- Measure:
-
HULFT-SAN is not installed. Check the corresponding host of the Host Information. It is not possible to send from HULFT to the host for which Connection Type (CONNECTTYPE) is SAN connection.
30 Cannot open snd information.
- Description:
-
Access to Send Management Information file failed.
- Measure:
-
An access error to the Send Management Information file (hulsnd.db.dat) occurred. Check the permissions and status of the environment variable 'HULPATH.'
31 Cannot open rcv information.
- Description:
-
Access to Receive Management Information file failed.
- Measure:
-
An access error to the Receive Management Information file (hulrcv.db.dat) occurred. Check the permissions and status of the environment variable 'HULPATH.'
32 Cannot open job information.
- Description:
-
Access to Job Information file failed.
- Measure:
-
An access error to the Job Information file (hulexec.db.dat) occurred. Check the permissions and status of the environment variable 'HULPATH.'
33 Cannot open host information.
- Description:
-
Access to the Host Information file failed.
- Measure:
-
An access error to the Host Information file (hulhosts.db.dat) occurred. Check the permissions and status of the environment variable 'HULPATH.'
34 Cannot open group information.
- Description:
-
Access to the Transfer Group Information file failed.
- Measure:
-
An access error to the Transfer Group Information file (hulrhost.db.dat) occurred. Check the permissions and status of the environment variable 'HULPATH.' Also, when you executed a Send Request, check whether the Transfer Group ID has been registered in the Receive Management Information.
35 Cannot open fmt information.
- Description:
-
Access to the Format Information file failed.
- Measure:
-
An access error to the Format Information file (hulfmt.db.dat) occurred. Check the permissions and status of the environment variable 'HULPATH.'
36 Cannot open sys information.
- Description:
-
Access to the System Environment Settings file failed.
- Measure:
-
An access error to the System Environment Settings file (hulenv.conf) occurred. Check the permissions and status of the environment variable 'HULPATH.'
37 Cannot open snd log.
- Description:
-
Access to the Send Log file failed.
- Measure:
-
An access error to the Send Log file (hulsndlog.dat, hulsndlog.sw.dat) occurred. Check the permissions and status of the environment variable 'HULPATH.'
38 Cannot open rcv log.
- Description:
-
Access to the Receive Log file failed.
- Measure:
-
An access error to the Receive Log file (hulrcvlog.dat, hulrcvlog.sw.dat) occurred. Check the permissions and status of the environment variable 'HULPATH.'
39 Cannot open snd job log.
- Description:
-
Access to the Post-send Job Execution Log failed.
- Measure:
-
An access error to the Post-send Job Execution Log file (hulexeclogs.dat, hulexeclogs.sw.dat) occurred. Check the permissions and status of the environment variable 'HULPATH.'
40 Cannot open rcv job log.
- Description:
-
Access to the Post-receive Job Execution Log file failed.
- Measure:
-
An access error to the Post-receive Job Execution Log file (hulexeclogr.dat, hulexeclogr.sw.dat) occurred. Check the permissions and status of the environment variable 'HULPATH.'
41 Cannot open req log.
- Description:
-
Access to Observe Log file failed.
- Measure:
-
An access error to the Observe Log file (hulaccreqlog.dat, hulaccreqlog.sw.dat) occurred. Check the permissions and status of the environment variable 'HULPATH.'
42 Cannot open sending queue log.
- Description:
-
Access to the Send Control file (sddsendlist.dat) failed.
- Measure:
-
An access error to the Send Control file (sddsendlist.da) occurred. Check the permissions and status of the environment variable 'HULPATH.'
45 Cannot open XXX file.
- Description:
-
Access to various files failed.
- Measure:
-
An access error of the file occurred. Check the permissions and status of the environment variable 'HULPATH.'
46 Cannot open PPP client file.
- Description:
-
Access to the PPP client management file failed.
- Measure:
-
An access error of the file occurred. Check the permissions and status of the environment variable 'HULPATH.'
47 Cannot open multi format file.
- Description:
-
Access to the Multi Format Information file failed.
- Measure:
-
An access error of the file occurred. Check the permissions and status of the environment variable 'HULPATH.'
48 Cannot open output message file.
- Description:
-
Access to the message output file failed.
- Measure:
-
Check the permissions and status of the message output file.
49 Cannot open opration log. (Type:File Access Log/Type:Command Execution Log)
- Description:
-
Access to the Operation Log file failed.
- Measure:
-
An access error of the file. Check the permissions and status of opl under the environment variable 'HULPATH' (HULPATH/opl).
50 Cannot lock file.
- Description:
-
Lock to various files failed.
- Measure:
-
A lock error of the file. Check the permissions and status of the environment variable 'HULPATH.'
51 Cannot unlock file.
- Description:
-
Unlock of various files failed.
- Measure:
-
An unlock error of the file. Check the permissions and status of the environment variable 'HULPATH.'
52 Cannot close file.
- Description:
-
Closing of various files failed.
- Measure:
-
An access error of the file occurred. Check the permissions and status of the environment variable 'HULPATH.'
53 Cannot read file.
- Description:
-
Access to the file failed.
- Measure:
-
An access error to the environment file occurred. Check the permissions and status of the environment variable 'HULPATH.' If necessary, change and re-execute.
54 Cannot copy file.
- Description:
-
Copying of the file failed.
- Measure:
-
An access error of the file occurred. Check the permissions and status of the environment variable 'HULPATH.'
55 Cannot move file.
- Description:
-
Copying of the file failed.
- Measure:
-
An access error of the file occurred. Check the permissions and status of the environment variable 'HULPATH.'
56 Cannot delete record.
- Description:
-
Deletion of the record failed.
- Measure:
-
An access error of the file occurred. Check the permissions and status of the environment variable 'HULPATH.'
57 Not found ID.
- Description:
-
Specified ID does not exist.
- Measure:
-
Specify an ID existing in the Management Information and re-execute.
58 Over max count.
- Description:
-
The specified value has exceeded the upper limit value.
- Measure:
-
Check the content of the parameter and re-execute.
59 Cannot get filesize.
- Description:
-
Acquisition of the file size failed.
- Measure:
-
An access error of the file occurred. Check the permissions and status of the environment variable 'HULPATH.'
60 A connect socket error.
- Description:
-
Socket connection failed.
- Measure:
-
Connection of the socket failed. Check the port number of the remote host.
61 A read socket error.
- Description:
-
Reading of the communications buffer failed.
- Measure:
-
The line may have been disconnected. Check the status of the line, and try again.
62 A write socket error.
- Description:
-
Writing of the communication buffer failed.
- Measure:
-
The line may have been disconnected. Check the status of the line, and try again.
63 Send daemon received the term request and ended.
- Description:
-
Issuance of the request failed because the termination process of the Send daemon is ongoing.
- Measure:
-
Start up the Send daemon and issue the request again.
64 Cannot open trg information.
- Description:
-
Access to the File Trigger Information file failed.
- Measure:
-
An access error of the file occurred. Check the permissions and status of the environment variable 'HULPATH.'
65 Usage
- Description:
-
A parameter error occurred.
- Measure:
-
Specify the correct parameter.
72 Illegal date range.
- Description:
-
An error in the specified date.
- Measure:
-
Specify the correct date.
73 A filename error.
- Description:
-
Access to various files failed.
- Measure:
-
Check the specified file name.
74 No target data.
- Description:
-
Specified data was not found.
- Measure:
-
Check the parameters. Correct and re-execute the command if necessary.
75 QUIT.
- Description:
-
The command ended because the file specified with the command parameter does not exist.
76 A server error.
- Description:
-
An error occurred in the remote host.
- Measure:
-
Check the error details of the remote host.
77 A resend error.
- Description:
-
A resending error of the Alert Resend command.
- Measure:
-
Details are output to the log of the Alert Resend command. Please check.
78 All of sending were canceled.
- Description:
-
In the Synchronous Transfer, all of sending were cancelled.
79 Some of sending were canceled.
- Description:
-
When multicasting in the Synchronous Transfer, some of sending were cancelled.
80 A server error.
- Description:
-
An error occurred in the host that acknowledged the request during remote job execution.
- Measure:
-
Check the log on the requestee side.
81 A job execute error.
- Description:
-
Job during remote job execution terminated abnormally.
- Measure:
-
Check the log of the job execution side.
82 A socket error.
- Description:
-
A socket error at the time of remote job execution.
- Measure:
-
There may be an error in the socket stream, and so on. Check the environment.
83 Job ID is not found.
- Description:
-
Job ID is not registered.
- Measure:
-
Check the Job Information of the job execution side.
84 A file access error.
- Description:
-
Access to the file failed.
- Measure:
-
An access error of the file occurred. Check the permissions and the status of the environment variables 'HULPATH' and 'HULEXEP.'
85 Job time out.
- Description:
-
The job ended abnormally due to timeout.
- Measure:
-
Check the content of the job and re-execute.
86 A log file open error.
- Description:
-
Opening of the log file during remote job execution file failed.
- Measure:
-
An access error of the file occurred. Check the permissions and the status of HULPATH and the various displayed files.
87 A log file write error.
- Description:
-
Writing of the log file at the time of remote job execution failed.
- Measure:
-
An access error of the file occurred. Check the permissions and status of the environment variable 'HULPATH' and the various displayed files.
88 A memory error.
- Description:
-
An memory error during remote job execution.
- Measure:
-
Check the environment of the operating system, and re-execute.
89 A parameter error.
- Description:
-
A parameter error during the remote job execution.
- Measure:
-
Check the argument, and re-execute.
90 A version error
- Description:
-
The IP Version (ipversion) of the System Environment Settings is invalid.
- Measure:
-
Set a correct value to IP Version (ipversion) of the System Environment Settings.
91 Duplicated request.
- Description:
-
The request has already been acknowledged.
94 Failed to communicate in the Forced Strong Key mode.
- Description:
-
Failed to communicate in the Forced Strong Key mode.
- Measure:
-
Check that all of the following conditions are met on the destination host:
-
Forced Strong Key mode is enabled
-
HULFT Ver.8.4.0 or higher is installed
-
HULFT8 Cipher Option(AES) is installed
-
95 Illegal data.
- Description:
-
There is an error in the data contents.
- Measure:
-
Check the specification of the parameter and the data contents.
96 No corresponding transmission information.
- Description:
-
Target transfer does not exist.
- Measure:
-
Check the specified parameter (host name, File ID and the like) of the command.
97 Failed to release the space of unused file records.
- Description:
-
Failed to release the space of unused file records.
- Measure:
-
Check the current permissions and setting for the environment variable HULPATH, the state of the file, free disk space, and so on, and run the command again.
98 Instant transfer cannot be performed because Forced Strong Key mode is enabled.
- Description:
-
Instant transfer cannot be performed because Forced Strong Key mode is enabled.
- Measure:
-
Check the setting of the Forced Strong Key mode (strongkeymode) in the System Environment Settings.
99
- Description:
-
Registration of management information by the management information batch registration failed.
- Measure:
-
There is an error in the description format of the parameter file, specification method of the field or in the specified parameter of the command. Check the parameter file, specified parameter of the command, and re-execute.
101 A parameter error.
- Description:
-
There is an error in the startup parameter when the Job Execution Result Notification is executed.
- Measure:
-
Check the contents of the parameter.
102 Get environment error.
- Description:
-
Acquiring an environment variable failed during the execution of the Job Execution Result Notification.
- Measure:
-
Check the Shell script where the Job Information of Post-receive Job and the command have been registered.
103 A connection error.
- Description:
-
The connection to the Observe daemon of the sending side failed during the execution of the Job Execution Result Notification.
- Measure:
-
Check that the Observe daemon of the sending side has started, and check the Observe Port No. in the Host Information of the receiving side as well as the port no. of the Observe daemon of the sending side.
104 A write file error.
- Description:
-
Writing the communication socket or the file failed during the execution of the Job Execution Result Notification.
- Measure:
-
There may be an error in the socket stream, file system, or the operating system and so on. Check the environment.
105 A read file error.
- Description:
-
Reading from the communication socket or the file failed during the execution of the Job Execution Result Notification.
- Measure:
-
There may be an error in the socket stream, file system, or the operating system and so on. Check the environment.
106 A host information error.
- Description:
-
There is an error in the registration of the Host Information during the execution of the Job Execution Result Notification.
- Measure:
-
Check the Host Information.
107 A service file error.
- Description:
-
There is an error in the contents of the Observe Definition file (service.db) during the execution of the Job Execution Result Notification.
- Measure:
-
Check the contents of the Observe Definition file (service.db).
108 A write error.
- Description:
-
Writing the communication socket or the file failed during the execution of the Job Execution Result Notification.
- Measure:
-
There may be an error in the socket stream, file system, or the operating system and so on. Check the environment.
109 A read error.
- Description:
-
Reading from the communication socket or the file failed during the execution of the Job Execution Result Notification.
- Measure:
-
There may be an error in the socket stream, file system, or the operating system and so on. Check the environment.
110 Message file open error.
- Description:
-
Opening of the notification message output destination file failed during the execution of the Job Execution Result Notification.
- Measure:
-
Check the contents of the Observe Definition file (service.db).
111 A hostname error.
- Description:
-
Acquisition of the host name failed during the execution of the Job Execution Result Notification.
- Measure:
-
There may be an error in the socket stream, operating system, or other failure may have occurred. Check the environment.
112 A server error.
- Description:
-
Cancelled from the sending side during the execution of the Job Execution Result Notification.
- Measure:
-
The sending side (requestee side) is abnormal. Re-execute after checking.
113 A server error.
- Description:
-
Abnormality occurred in the Observe daemon during the execution of the Job Execution Result Notification.
- Measure:
-
The sending side (requestee side) is abnormal. Re-execute after checking.
114 A memory error.
- Description:
-
Acquisition of memory failed.
- Measure:
-
Check the environment of the operating system, and re-execute.
118 A version error.
- Description:
-
Version error occurred.
- Measure:
-
Version mismatch has occurred in the connection to HULFT Product. Check the version of HULFT Product.
120 put environment error.
- Description:
-
Failed to set the environment variable.
- Measure:
-
Check the environment of the operating system, and re-execute.
121 A screen error.
- Description:
-
Failed to create the environment for the screen.
- Measure:
-
Check the environment of the operating system, and re-execute.
122 knjcode error.
- Description:
-
Failed to acquire the Kanji Code Type (knjcode) in the System Environment Settings.
- Measure:
-
Check the setting of the Kanji Code Type (knjcode) in the System Environment Settings.
124 ID cannot be longer than 8 bytes.
- Description:
-
The remote host is lower than HULFT Ver.8, or the Use HULFT7 Comm.Mode (hul7mode) in the Host Information is set to 'Y (enabled).' ID with a size of 9 bytes or more cannot be used for the Management Information.
- Measure:
-
Specify each ID within 8 bytes in the Management Information.
125 hullang error.
- Description:
-
Failed to acquire HULFT Operation Language (hullang).
- Measure:
-
Check the settings of HULFT Operation Language (hullang) in the System Environment Settings.
126 datefmt error.
- Description:
-
Failed to acquire Date Format.
- Measure:
-
Check the setting of Date Format in the System Environment Settings.
127 Code Set Combination error.
- Description:
-
The combination of the following two code sets is not supported:
-
The code set specified for Code Set for Transfer (cs4trnsfr) in the System Environment Settings on the local host
-
The code set specified for Code Set for Transfer in the System Environment Settings on the host that created the joined file
-
- Measure:
-
Check supported combinations of code sets.
128 Combination Error with EBCDIC Set.
- Description:
-
The combination of the following two code sets is not supported:
-
The code set specified for Code Set for Transfer in the System Environment Settings on the host that created the joined file
-
The code set specified for EBCDIC set with a parameter on the local host
-
- Measure:
-
Check supported combinations of code sets.