Error codes for Receive Management Information

END has not been entered in parameter file.

Enter END in the end of each management information.

Incorrect specifications exist for the registration mode.

Enter correct registration mode. (NEW, REP, MOD)

Specified Error Handling is incorrect.

Enter correct Error Handling type. (DELETE, KEEP, RESTORE)

Specified receive mode is incorrect.

Enter correct receive mode. (SINGLE, MULTI)

Receive file name not specified.

Enter the receive file name.

The registration mode is not specified.

Enter the registration mode.

The Error Recovery is not specified.

Enter Error Handling.

The receive mode is not specified.

Specify receive mode.

The receive file name exceeds 33 bytes.

Enter the receive file name within 33 characters.

The successful job ID exceeds the maximum length of 50 bytes.

Shorten the Successful Job ID to 50 bytes or less.

The Comment exceeds 60 bytes.

Enter the Comment in less than 60 characters.

The transfer group ID exceeds the maximum length of 50 bytes.

Shorten the transfer group ID to 50 bytes or less.

When the receive mode is Multiple Receive, the registration mode is not Append mode.

Change the receive mode to Single Receive or the registration mode to Append mode.

Specified tag name is incorrect.

Enter the correct tag name.

The EBCDIC Code Set is incorrect.

Specify correct code set. (0, A-I, V-X)

The record length is incorrect.

Specify correct the record length. (1-32766)

The EBCDIC code set has not been specified.

Enter the EBCDIC code set.

The record length is not specified.

Enter the record length.

The unsuccessful job ID exceeds the maximum length of 50 bytes.

Shorten the unsuccessful job ID to 50 bytes or less.

The file ID exceeds the maximum length of 50 bytes.

Shorten the file ID to 50 bytes or less.

File ID has not been specified.

Enter the file ID.

Generational Management is incorrect.

Enter a correct value for Generational Management (Y or N).

The Generational Management has not been specified.

Enter the Generational Management.

Specified receive mode is incorrect.

A combination of Registration Mode and Generational File and Error Handling is incorrect. Specify with a correct combination.

The cipher key is too long or too short.

If Forced Strong Key mode is enabled, set 64 digits hexadecimal character strings as the cipher key.
If Forced Strong Key mode is disabled, omit the cipher key, or set 8 to 20 bytes of alphanumeric character.

Transfer using ciphers is not available.

HULFT Cipher Option has not been installed. Do not specify the Cipher Key.

Error found in the receive file name specification.

Please check the receive file name specification.

When Generational Management is specified, the member name of the physical file or the archive file name exceeds 6 bytes.

Enter the member name of physical file or the archive file name to less than 6 bytes.

Notification is incorrect.

Set the correct notification. (T,J)

The combination of Generational Management and the No. of Generations is incorrect.

In case Generational Management (GENCTL) is set to "Y", specify No. of Generations (GENMNGNO) as a number in the range from 2 to 9999.When Generational Management is (GENCTL) is set to "N", specify No. of Generations (GENMNGNO) as "0".

The No. of Generations is incorrect.

Specify a valid value for No. of Generations. (0 or 2 through 9999)

The receive mode when &SNDFILE and &MSGn (n is in range of 0 to 5) are specified in the receive file name is incorrect.

Change the receive file name or set Receive Mode to "S".

The data verification is not correct.

Set the correct value for the Verify Data specifying either "0" or "1" as appropriate.

The file ID is incorrect.

Enter the file ID in alphanumeric characters within 50 bytes, which begin with an alphabetic character.

Successful job ID is incorrect.

Enter the successful job ID in alphanumeric characters within 50 bytes, which begin with an alphabetic character.

Unsuccessful job ID is incorrect.

Enter the unsuccessful job ID in alphanumeric characters within 50 bytes, which begin with an alphabetic character.

The transfer group ID is incorrect.

Enter the transfer group ID in alphanumeric characters within 50 bytes, which begin with an alphabetic character.

Cipher Key (PASSWORD) is specified but invalid.

If Forced Strong Key mode is enabled, specify a character string of 64 bytes, consisting of from "0" through "9" and from "A" through "F", to Cipher Key (PASSWORD).