Output of the default values in the System Environment
You can perform batch processing on the default values configured in the System Environment to output them to a file.
System Environment Settings Default Value Output Program (XRPRMGEN)
Program Name
XRPRMGEN
Output Image
START-TASK=HULSND UNIT=SYSDA PORTNO=30000 TCPIP=TCPIP TASK-CNT=5 TASK-ABEND=CONTINUE HOST-NAME=MVS HSTCHA=L DATACHK=N RETRY=3 RESENDDEL=0 PREFIX=XR RECLEN=N JOBTIME=15 TIMEOUT=3600 SCANMODE=N RCVOVER-RTY=0 CLEARMODE=B ENDERRMODE=0 STATUSDISPLAY=1 TGRPCHK=0 HSTCHK=0 LOGDELTHRESHOLD=0 EBCDIC=0 PSCHG=0 PSASCII=1 PSEBCDIC=1 GAIJIFILE=0 GAIJIERR=0 DYNAMIC-DIRECT=N INIT-UNIT=SYSDA WORKVOLMODE=0 JESC=$ SNDRETRY=10 SNDRTIME=10 EUCSP=1 SOCKERR-AUTORETRY=0 RETRYTIME=0 MSGDYNPARM=3 RECV-TASK=HULRCV CIPHERTYPE=0 CLASS=A MSGCLASS=B SNDBNO=5 RCVBNO=5 REQWAITMODE=0 DEFER=0 JCLRETRY=0 JCLRTIME=0 PROCTRANSTYPE=A USRIDCHKMODE=0 OPLSELECT=0 CNVLENCHK=0 HULLANG=JPN DATEFMT=1 SNDSOCKSIZE=0 RCVSOCKSIZE=0 SND-SEQNO-THRESHOLD=0 RESND-QUELISTNO-THRESHOLD=0 TTMODE=0 TTRCVOMIT=0 TTRCVFILOUTPUT=0 TTPRESNDJOB=0 TTSNDJOB=0 TTRCVJOB=0 TTSNDRCVLOG=1 OUTSTSKID=N CNSSELECT=0 RPREFIX=XRM HULCHARSET=939 CS4TRNSFR=I INDOPTVAR=0 LISTEN=0 SND-START-MODE=WARM RCV-APPLNM=HULRCV RCV-MAXCON=16 RCV-RECCHK=N RCV-FILE-WAIT=N RCV-FILE-SEARCH=V RCV-FILE-RETRY=0 RCV-FILE-RTIME=0 RCV-JOBWTIME=15 RCV-CHRSET=0 RCV-TIMEOUT=0 APT-APPLNM=HULSRV APT-MAXCON=16 APT-TIMEOUT=0 ALLOWSNDREQ=Y ALLOWPOSTRJOBRSLT=Y ALLOWJOBRSLTNTFY=Y ALLOWRMTJOBEXE=Y ALLOWINSTTRANS=N INSTTRANSCODCNV=R INSTTRANSEBCDIC=0 INSTTRANSRCVSPACE=(CYL,(5,3),RLSE) INSTTRANSRCVDCB=(RECFM=VB,LRECL=256,BLKSIZE=6233) INSTTRANSMFRCVORG=S CONSOLELOG=111 STRONGKEYMODE=0 CODE-CONVERSION-LOCATION=ANY
The values shown above are only an example. The actual values will vary according to the environment.
Example of JCL
//XRPRMGEN JOB CLASS=A,MSGCLASS=B //XRPRMGEN EXEC PGM=XRPRMGEN,REGION=4096K //STEPLIB DD DSN=HULFT.LOAD,DISP=SHR //XRSYSIN DD DUMMY //XRGEN DD DSN=HULFT.FILE.OUT,DISP=(NEW,KEEP,DELETE),UNIT=SYSDA, // VOL=SER=HUL001,DCB=(BLKSIZE=6160,LRECL=80,RECFM=FB), // SPACE=(CYL,(5,1),RLSE) //SYSOUT DD SYSOUT=* //SYSUDUMP DD SYSOUT=* //
|
DD Name |
Value |
Description |
|---|---|---|
|
STEPLIB |
HULFT.LOAD |
HULFT load module library |
|
XRGEN |
HULFT.FILE.OUT |
Output File |
|
Parameter Name |
Value |
Description |
|---|---|---|
|
UNIT |
SYSDA |
UNIT |
|
VOL=SER |
HUL001 |
Volume Name |
Status Code
|
Status Code |
Description |
|---|---|
|
0 |
Outputting the default values in the System Environment was completed successfully. |
|
12 |
An error occurred while outputting the default values in the System Environment. |
For details about messages, refer to the following:
HULFT10 for zOS Error Codes and Messages :