Send Request messages
* XRRCVREQ * MANAGEMENT FILE OPEN FAILED
- Description:
-
Failed to open the Send and Receive Management file (HULFT.FILE).
- Measures:
-
A failure has occurred in the Send and Receive Management file (HULFT.FILE). Refer to the VSAM detail code and take the appropriate measures.
* XRRCVREQ * FILE INF GET ERROR
- Description:
-
Failed to read the Receive Management Information.
- Measures:
-
Check the Send Management Information and the Receive Management Information.
* XRRCVREQ * HOST INF GET ERROR
- Description:
-
Failed to read the Host Information.
- Measures:
-
Check the Host Information.
* XRRCVREQ * HGP INF GET ERROR
- Description:
-
Failed to read the Transfer Group Information.
- Measures:
-
Check the Send Management Information and the Receive Management Information.
* XRRCVREQ * ISP OPEN FAILED RC=code
- code:
-
Communication error code (Refer to Communication error code list.)
- Description:
-
Failed to open TCPIP for MVS.
- Measures:
-
TCPIP for MVS may not be running, the TCPIP for MVS application name may not be defined, or there could be another cause. Take the appropriate measures based on the communication error code and try again.
* XRRCVREQ * ISP CONN FAILED RC=code H=host
- code:
-
Communication error code (Refer to Communication error code list.)
- host:
-
Remote host name
- Description:
-
Failed to connect to the remote host.
- Measures:
-
The Observe program on the remote host is not running. The Port No. for the Observe program may be incorrect, or there could be another cause. Take the appropriate measures based on the communication error code and try again.
* XRRCVREQ * ISP CONV FAILED RC=code
- code:
-
Communication error code (Refer to Communication error code list.)
- Description:
-
Failed to communicate with the remote host.
- Measures:
-
The Observe function may have ended on the remote host, or there could be another cause. Take the appropriate measures based on the communication error code and try again.
* XRRCVREQ * SEND REQ ERROR RC=code F=fileid
H=host
- code:
-
Status code sent from the remote host (If the platform of the remote host is Mainframe, refer to Status codes and detail codes for Observe processing. If it is not Mainframe, refer to Error Codes and Messages manual for the applicable host.)
- fileid:
-
File ID
- host:
-
Remote host name
- Description:
-
The Send Request was not acknowledged successfully.
- Measures:
-
Look up the status code, take the appropriate measures, and try again. If you are using HULFT-HUB, check HULFT-HUB.
* XRRCVREQ * PARAMETER CARD ERROR
- Description:
-
The definition method of the XRCRD definition card is incorrect.
- Measures:
-
Check the XRCRD definition card in the JCL.
* XRRCVREQ * PRODUCT VERSION ERROR
- Description:
-
A version inconsistency occurred in the connection to the destination product.
- Measures:
-
Check the supported version.
* XRRCVREQ * ID LENGTH ERROR PARAMETER=FILEID VALUE=value
- value:
-
ID setting value
- Description:
-
An ID of 9 bytes or more cannot be specified, either because the Use HULFT7 Comm. Mode is enabled, or because the version of HULFT on the Observe system side is HULFT7 or lower.
- Measures:
-
Specify an ID within 8 bytes.
* XRRCVREQ * RECONNECT ON HULFT7 MODE
- Description:
-
HULFT will reconnect in HULFT7 communication mode, because the version of HULFT on the Observe system side is HULFT7 or lower.
* XRRCVREQ * MSGL IS UNAVAILABLE
- Description:
-
The Long Message cannot be used, because the Use HULFT7 Comm. Mode is enabled, or because the version of HULFT on the Observe system side is HULFT7 or lower.
Long messages are invalid.
* XRRCVREQ * PROTOCOL VERSION IS 8 OR OVER
- Description:
-
Although the version of HULFT on the host on the Observe system side is HULFT Ver.8 or higher, the Use HULFT7 Comm. Mode is enabled.
* XRRCVREQ * _INSTANT_TRANSFER_ IS A SYSTEM-RESERVED WORD
- Description:
-
Cannot execute the Send Request request because the file ID "_INSTANT_TRANSFER_" is a system-reserved word.
* XRRCVREQ * REQUESTS CANNOT BE ISSUED IN FORCED STRONG KEY MODE BECAUSE USE HULFT7 COMM. MODE IS SET TO "Y"
F=fileid
H=host
- fileid:
-
File ID
- host:
-
Host Name
- Description:
-
The Forced Strong Key mode is enabled, but because the HULFT7 communication mode is enabled, communication failed.
- Measures:
-
Disable the HULFT7 communication mode and reissue the request.
* XRRCVREQ * FAILED TO COMMUNICATE IN FORCED STRONG KEY MODE
F=fileid
H=host
- fileid:
-
File ID
- host:
-
Host Name
- Description:
-
The Forced Strong Key mode is enabled, but because the remote host is lower than V8.4 or the Forced Strong Key mode is disabled on the remote host, communication failed.
- Measure 1:
-
Check the version of the remote host.
- Measure 2:
-
Check whether the Forced Strong Key mode is enabled on the remote host.