Remote Job Execution messages
* XRRJOBEX * MANAGEMENT FILE OPEN FAILED
- Description:
-
Failed to open the Send and Receive Management file (HULFT.FILE).
- Measures:
-
Check if the Send and Receive Management file (HULFT.FILE) was created correctly.
* XRRJOBEX * HOST INF GET ERROR
- Description:
-
Failed to read the Host Information.
- Measures:
-
Check if the Send and Receive Management file (HULFT.FILE) was created correctly.
* XRRJOBEX * PARAMETER ERROR
- Description:
-
The specification for the execution parameter is not correct.
- Measures:
-
Correct the setting, and try again.
* XRRJOBEX * UNDEFINE OPERAND
- Description:
-
The specified operand is incorrect.
- Measures:
-
Correct the setting, and try again.
* XRRJOBEX * JOBID PARAMETER ERROR
- Description:
-
The JOBID operand is not specified.
- Measures:
-
The JOBID operand is a required parameter. Set this parameter correctly.
* XRRJOBEX * EXEC-HOST PARAMETER ERROR
- Description:
-
The EXEC-HOST operand is not specified.
- Measures:
-
The EXEC-HOST operand is a required parameter. Set this parameter correctly.
* XRRJOBEX * TIMEOUT PARAMETER ERROR
- Description:
-
The TIMEOUT operand is set with characters other than numbers, or is specified outside the valid range.
- Measures:
-
Specify the TIMEOUT operand using numbers within the valid range.
* XRRJOBEX * ISP OPEN FAILED RC=code
- code:
-
Communication error code (Refer to Communication error code list.)
- Description:
-
Failed to open TCPIP for MVS.
- Measures:
-
TCPIP for MVS is not running. The TCPIP for MVS application name may not be defined, or there could be another cause. Take the appropriate measures for the communication error code, and try again.
* XRRJOBEX * ISP CONN FAILED RC=code
- code:
-
Communication error code (Refer to Communication error code list.)
- Description:
-
Failed to connect to the remote host.
- Measures:
-
The Observe function may not have started on the remote host, the Observe port number may be incorrect, or there could be another cause. Take the appropriate measures for the communication error code, and try again.
* XRRJOBEX * ISP CONV FAILED RC=code
- code:
-
Communication error code (Refer to Communication error code list.)
- Description:
-
Failed to communicate with the remote host.
- Measures:
-
The Observe function may have ended on the remote host, or there could be another cause. Take the appropriate measures for the communication error code, and try again.
* XRRJOBEX * JOB EXEC ERROR RC=code
- code:
-
Error code (Refer to Error code list.)
- Description:
-
Job execution failed.
- Measures:
-
Check the content of the error code and take the appropriate measures.
* XRRJOBEX * JOB EXECUTION COMPLETE
- Description:
-
Job execution ended successfully.
* XRRJOBEX * HULRJOB ERROR RC=code
- code:
-
Status code sent from the remote host (Refer to Status codes and detail codes for Observe processing.)
- Description:
-
The Remote Job Execution (HULRJOB) was not acknowledged correctly.
- Measures:
-
Look up the status code, take the appropriate measures, and try again.
* XRRJOBEX * TIMEOUT PARAMETER IS CHANGED : WARNING
- Description:
-
Since the value specified for TIMEOUT is outside the valid range, if the specified value is '9' or less it is changed to '10,' and if it is '259201' or greater it is changed to '259200.'
- Measures:
-
The processing was carried out successfully. Specify a value between 10 and 259200 for TIMEOUT.
* XRRJOBEX * ID LENGTH ERROR
- Description:
-
An ID of 9 bytes or more cannot be specified, either because the Use HULFT7 Comm. Mode is enabled, or because the version of HULFT on the Observe system side is HULFT7 or lower.
- Measures:
-
Specify an ID within 8 bytes.
* XRRJOBEX * RECONNECT ON HULFT7 MODE
- Description:
-
HULFT will reconnect in HULFT7 communication mode, because the version of HULFT on the Observe system side is HULFT7 or lower.
* XRRJOBEX * PROTOCOL VERSION IS 8 OR OVER
- Description:
-
The version of HULFT on the Observe system side is HULFT8 or higher. Disable the Use HULFT7 Comm. Mode to use newly-introduced functions.
* XRRJOBEX * PARAMETER CARD ERROR
- Description:
-
There is an error on the definition card.
- Measures:
-
Correctly define the definition card, and try again.
* XRRJOBEX * REQUESTS CANNOT BE ISSUED IN FORCED STRONG KEY MODE BECAUSE USE HULFT7 COMM. MODE IS SET TO "Y"
- Description:
-
The Forced Strong Key mode is enabled, but because the HULFT7 communication mode is enabled, communication failed.
- Measures:
-
Disable the HULFT7 communication mode and reissue the request.
* XRRJOBEX * FAILED TO COMMUNICATE IN FORCED STRONG KEY MODE
- Description:
-
The Forced Strong Key mode is enabled, but because the remote host is lower than V8.4 or the Forced Strong Key mode is disabled on the remote host, communication failed.
- Measure 1:
-
Check the version of the remote host.
- Measure 2:
-
Check whether the Forced Strong Key mode is enabled on the remote host.