Official | Output message

I0011006: MSG=Connection close. IPADDRESS=%s

Message Level:: I

I0011015: MSG=Acquired the socket buffer size (SO_SNDBUF) from the operating system successfully. SNDSOCKSIZE=%d

Message Level:: I

I0011016: MSG=Acquired the socket buffer size (SO_RCVBUF) from the operating system successfully. RCVSOCKSIZE=%d

Message Level:: I

I0011018: MSG=HULFT uses the maximum value of SNDSOCKSIZE in the operating system for its own SNDSOCKSIZE. SNDSOCKSIZE=%d

Message Level:: I

I0011019: MSG=HULFT uses the maximum value of RCVSOCKSIZE in the operating system for its own RCVSOCKSIZE. RCVSOCKSIZE=%d

Message Level:: I

I0013003: MSG=Job exec start. JOBID=%s EXECJOB=%s

Message Level:: I

I0013004: MSG=Job exec end. JOBID=%s EXECJOB=%s JOBSTS=%d

Message Level:: I

I0013007: MSG=Job exec start. JOBID=%s EXECJOB=%s

Message Level:: I

I0013008: MSG=Job exec end. JOBID=%s EXECJOB=%s JOBSTS=%d

Message Level:: I

I0016003: MSG=Set value. PARAM=%s VALUE=%s

Message Level:: I

I0016018: MSG=Use default value. PARAM=%s VALUE=%s

Message Level:: I

W0002004: MSG=Failed to lock the Exclusive Control file. FILENAME=%s STRERROR=%s

Message Level:: W

W0003001: MSG=Operation log directory access error. STRERROR=%s

Message Level:: W

W0003002: MSG=Operation log open error. STRERROR=%s

Message Level:: W

W0003003: MSG=Operation log allocate error. STRERROR=%s

Message Level:: W

W0003004: MSG=Operation log move error. STRERROR=%s

Message Level:: W

W0003005: MSG=Operation log write error. STRERROR=%s

Message Level:: W

W0003006: MSG=Operation log allocate error. STRERROR=%s

Message Level:: W

W0003007: MSG=Operation log open error. STRERROR=%s

Message Level:: W

W0011020: MSG=Connection timeout. IPADDRESS=%s

Message Level:: W

W0011021: MSG=MSG=Exceeded the maximum number of file descriptors that can be obtained in this process. IPADDRESS=%s

Message Level:: W

Measure:: Wait until other processing ends, and retry the processing.

W0013002: MSG=Job information is not found. JOBID=%s

Message Level:: W

Measure:: Check that the relevant record is registered in the Job Information.

W0013005: MSG=Job exec end. JOBID=%s EXECJOB=%s JOBSTS=%d

Message Level:: W

W0013006: MSG=Job information is not found. JOBID=%s

Message Level:: W

Measure:: Check that the relevant record is registered in the Job Information.

W0013009: MSG=Job exec end. JOBID=%s EXECJOB=%s JOBSTS=%d

Message Level:: W

W0013011: MSG=Job exec force end.

Message Level:: W

W0016005: MSG=Value not set. PARAM=%s

Message Level:: W

Measure:: Check that a value is set to the tag in the System Environment Settings file (hulenv.conf).

W0016007: MSG=Tag not found. PARAM=%s

Message Level:: W

Measure:: Check that the tag is correctly set in the System Environment Settings file (hulenv.conf).

W0016009: MSG=Token '=' not found. PARAM=%s

Message Level:: W

Measure:: Check that the equal sign '=' is set in the tag in the System Environment Settings file (hulenv.conf).

W0016011: MSG=Range error. PARAM=%s VALUE=%s

Message Level:: W

Measure:: Check that the values set to the tags in the System Environment Settings file (hulenv.conf) are within the setting range.

W0016013: MSG=Path error. PARAM=%s VALUE=%s

Message Level:: W

Measure:: Check that the path set to the tag in the System Environment Settings file (hulenv.conf) is correct.

W0016015: MSG=String too long. PARAM=%s VALUE=%s

Message Level:: W

Measure:: Check that the value set to the tag in the System Environment Settings file (hulenv.conf) does not exceed the settable string length.

W0016017: MSG=Invalid value. PARAM=%s VALUE=%s

Message Level:: W

Measure:: Check that the available values are correctly described in the System Environment Settings file (hulenv.conf).

E0001001: MSG=Socket read error. IPADDRESS=%s STRERROR=%s

Message Level:: E

Measure:: There may be problems in the socket stream. Check the environment. Also, check that it is not disconnected forcibly.

E0002001: MSG=Failed to open the Exclusive Control Management file. FILENAME=%s STRERROR=%s

Message Level:: E

E0002002: MSG=Failed to lock the Exclusive Control Management file. FILENAME=%s STRERROR=%s

Message Level:: E

E0002003: MSG=Failed to open the Exclusive Control file. FILENAME=%s STRERROR=%s

Message Level:: E

E0002005: MSG=Failed to lock the Exclusive Control file. FILENAME=%s STRERROR=%s

Message Level:: E

E0002006: MSG=Failed to unlock the Exclusive Control Management file. FILENAME=%s STRERROR=%s

Message Level:: E

E0002007: MSG=Failed to unlock the Exclusive Control file. FILENAME=%s STRERROR=%s

Message Level:: E

E0002008: MSG=Failed to unlock the Exclusive Control Management file. FILENAME=%s STRERROR=%s

Message Level:: E

E0002009: MSG=Failed to truncate the Deletion Target List file. STRERROR=%s

Message Level:: E

E0002010: MSG=Failed to open the Deletion Target List file. FILENAME=%s STRERROR=%s

Message Level:: E

E0002011: MSG=Failed to lock the Deletion Target List file. FILENAME=%s STRERROR=%s

Message Level:: E

E0002012: MSG=Failed to seek the Deletion Target List file. STRERROR=%s

Message Level:: E

E0002013: MSG=Failed to write the Deletion Target List file. STRERROR=%s

Message Level:: E

E0002014: MSG=Failed to fsync the Deletion Target List file. STRERROR=%s

Message Level:: E

E0002015: MSG=Failed to unlock the Deletion Target List file. STRERROR=%s

Message Level:: E

E0002016: MSG=Failed to open the Deletion Target List file. FILENAME=%s STRERROR=%s

Message Level:: E

E0002017: MSG=Failed to unlink the Deletion Target List Temporary file. FILENAME=%s STRERROR=%s

Message Level:: E

E0002018: MSG=Failed to stat the Deletion Target List Temporary file. FILENAME=%s STRERROR=%s

Message Level:: E

E0002019: MSG=Failed to open the Deletion Target List Temporary file. FILENAME=%s STRERROR=%s

Message Level:: E

E0002020: MSG=Failed to seek the Deletion Target List Temporary file. STRERROR=%s

Message Level:: E

E0002021: MSG=Failed to seek the Deletion Target List Temporary file. STRERROR=%s

Message Level:: E

E0002022: MSG=Failed to read the Deletion Target List file. STRERROR=%s

Message Level:: E

E0002023: MSG=Failed to write the Deletion Target List Temporary file. STRERROR=%s

Message Level:: E

E0002024: MSG=Failed to fsync the Deletion Target List Temporary file. STRERROR=%s

Message Level:: E

E0002025: MSG=Failed to move the Deletion Target List Temporary file. TMPNAME=%s FILENAME=%s STRERROR=%s

Message Level:: E

E0002026: MSG=Failed to unlink the Deletion Target List Temporary file. FILENAME=%s STRERROR=%s

Message Level:: E

E0002027: MSG=Failed to unlink the Deletion Target List Temporary file. FILENAME=%s STRERROR=%s

Message Level:: E

E0002028: MSG=Failed to open the Deletion Target List Temporary file. FILENAME=%s STRERROR=%s

Message Level:: E

E0002029: MSG=Failed to move the Deletion Target List Temporary file. TMPNAME=%s FILENAME=%s STRERROR=%s

Message Level:: E

E0002030: MSG=Failed to unlink the Deletion Target List Temporary file. FILENAME=%s STRERROR=%s

Message Level:: E

E0002031: MSG=Failed to unlink the Deletion Target List Temporary file. TMPNAME=%s FILENAME=%s STRERROR=%s

Message Level:: E

E0004001: MSG=Socket read error. IPADDRESS=%s STRERROR=%s

Message Level:: E

Measure:: There may be problems in the socket stream. Check the environment. Also, check that it is not disconnected forcibly.

E0004002: MSG=Socket timeout. IPADDRESS=%s SOCKTIME=%d

Message Level:: E

E0005001: MSG=Process fork error. STRERROR=%s

Message Level:: E

Measure:: Check the memory usage and the number of processes.

E0005002: MSG=Socket read error. IPADDRESS=%s STRERROR=%s

Message Level:: E

Measure:: There may be problems in the socket stream. Check the environment. Also, check that it is not disconnected forcibly.

E0006001: MSG=Memory allocate error. STRERROR=%s

Message Level:: E

Measure:: Check the environment. Terminate any unnecessary applications when the memory is insufficient.

E0006002: MSG=Memory allocate error. STRERROR=%s

Message Level:: E

Measure:: Check the environment. Terminate any unnecessary applications when the memory is insufficient.

E0007001: MSG=Memory allocate error. STRERROR=%s

Message Level:: E

Measure:: Check the environment. Terminate any unnecessary applications when the memory is insufficient.

E0007002: MSG=Socket write error. IPADDRESS=%s STRERROR=%s

Message Level:: E

Measure:: There may be problems in the socket stream. Check the environment. Also, check that it is not disconnected forcibly.

E0007003: MSG=Memory allocate error. STRERROR=%s

Message Level:: E

Measure:: Check the environment. Terminate any unnecessary applications when the memory is insufficient.

E0007004: MSG=Socket read error. IPADDRESS=%s STRERROR=%s

Message Level:: E

Measure:: There may be problems in the socket stream. Check the environment. Also, check that it is not disconnected forcibly.

E0007005: MSG=Memory allocate error. STRERROR=%s

Message Level:: E

Measure:: Check the environment. Terminate any unnecessary applications when the memory is insufficient.

E0007006: MSG=Socket write error. IPADDRESS=%s STRERROR=%s

Message Level:: E

Measure:: There may be problems in the socket stream. Check the environment. Also, check that it is not disconnected forcibly.

E0007007: MSG=Socket read error. IPADDRESS=%s STRERROR=%s

Message Level:: E

Measure:: There may be problems in the socket stream. Check the environment. Also, check that it is not disconnected forcibly.

E0007008: MSG=Memory allocate error. STRERROR=%s

Message Level:: E

Measure:: Check the environment. Terminate any unnecessary applications when the memory is insufficient.

E0007009: MSG=Socket read error. IPADDRESS=%s STRERROR=%s

Message Level:: E

Measure:: There may be problems in the socket stream. Check the environment. Also, check that it is not disconnected forcibly.

E0007010: MSG=Socket write error. IPADDRESS=%s STRERROR=%s

Message Level:: E

Measure:: There may be problems in the socket stream. Check the environment. Also, check that it is not disconnected forcibly.

E0007011: MSG=Socket read error. IPADDRESS=%s STRERROR=%s

Message Level:: E

Measure:: There may be problems in the socket stream. Check the environment. Also, check that it is not disconnected forcibly.

E0007012: MSG=Memory allocate error. STRERROR=%s

Message Level:: E

Measure:: Check the environment. Terminate any unnecessary applications when the memory is insufficient.

E0007013: MSG=Socket read error. IPADDRESS=%s STRERROR=%s

Message Level:: E

Measure:: There may be problems in the socket stream. Check the environment. Also, check that it is not disconnected forcibly.

E0007014: MSG=Memory allocate error. STRERROR=%s

Message Level:: E

Measure:: Check the environment. Terminate any unnecessary applications when the memory is insufficient.

E0007015: MSG=Socket write error. IPADDRESS=%s STRERROR=%s

Message Level:: E

Measure:: There may be problems in the socket stream. Check the environment. Also, check that it is not disconnected forcibly.

E0007016: MSG=Socket read error. IPADDRESS=%s STRERROR=%s

Message Level:: E

Measure:: There may be problems in the socket stream. Check the environment. Also, check that it is not disconnected forcibly.

E0007017: MSG=Memory allocate error. STRERROR=%s

Message Level:: E

Measure:: Check the environment. Terminate any unnecessary applications when the memory is insufficient.

E0007018: MSG=Socket read error. IPADDRESS=%s STRERROR=%s

Message Level:: E

Measure:: There may be problems in the socket stream. Check the environment. Also, check that it is not disconnected forcibly.

E0007019: MSG=Memory allocate error. STRERROR=%s

Message Level:: E

Measure:: Check the environment. Terminate any unnecessary applications when the memory is insufficient.

E0007020: MSG=Data item not enough. datasize=%u

Message Level:: E

E0007021: MSG=Socket write error. IPADDRESS=%s STRERROR=%s

Message Level:: E

Measure:: There may be problems in the socket stream. Check the environment. Also, check that it is not disconnected forcibly.

E0007022: MSG=Socket read error. IPADDRESS=%s STRERROR=%s

Message Level:: E

Measure:: There may be problems in the socket stream. Check the environment. Also, check that it is not disconnected forcibly.

E0007023: MSG=Memory allocate error. STRERROR=%s

Message Level:: E

Measure:: Check the environment. Terminate any unnecessary applications when the memory is insufficient.

E0007024: MSG=Socket read error. IPADDRESS=%s STRERROR=%s

Message Level:: E

Measure:: There may be problems in the socket stream. Check the environment. Also, check that it is not disconnected forcibly.

E0007025: MSG=Memory allocate error. STRERROR=%s

Message Level:: E

Measure:: Check the environment. Terminate any unnecessary applications when the memory is insufficient.

E0007026: MSG=Data item not enough. datasize=%u

Message Level:: E

E0007027: MSG=Data item not enough. datasize=%u

Message Level:: E

E0007028: MSG=Data item not enough. datasize=%u

Message Level:: E

E0007029: MSG=Memory allocate error. STRERROR=%s

Message Level:: E

Measure:: Check the environment. Terminate any unnecessary applications when the memory is insufficient.

E0007030: MSG=Socket write error. IPADDRESS=%s STRERROR=%s

Message Level:: E

Measure:: There may be problems in the socket stream. Check the environment. Also, check that it is not disconnected forcibly.

E0007031: MSG=Socket read error. IPADDRESS=%s STRERROR=%s

Message Level:: E

Measure:: There may be problems in the socket stream. Check the environment. Also, check that it is not disconnected forcibly.

E0007032: MSG=Memory allocate error. STRERROR=%s

Message Level:: E

Measure:: Check the environment. Terminate any unnecessary applications when the memory is insufficient.

E0007033: MSG=Socket read error. IPADDRESS=%s STRERROR=%s

Message Level:: E

Measure:: There may be problems in the socket stream. Check the environment. Also, check that it is not disconnected forcibly.

E0007034: MSG=Socket timeout. IPADDRESS=%s SOCKTIME=%d

Message Level:: E

E0007035: MSG=Socket timeout. IPADDRESS=%s SOCKTIME=%d

Message Level:: E

E0007036: MSG=Socket timeout. IPADDRESS=%s SOCKTIME=%d

Message Level:: E

E0007037: MSG=Socket timeout. IPADDRESS=%s SOCKTIME=%d

Message Level:: E

E0007038: MSG=Socket timeout. IPADDRESS=%s SOCKTIME=%d

Message Level:: E

E0007039: MSG=Socket timeout. IPADDRESS=%s SOCKTIME=%d

Message Level:: E

E0007040: MSG=Socket timeout. IPADDRESS=%s SOCKTIME=%d

Message Level:: E

E0007041: MSG=Socket timeout. IPADDRESS=%s SOCKTIME=%d

Message Level:: E

E0007042: MSG=Socket timeout. IPADDRESS=%s SOCKTIME=%d

Message Level:: E

E0007043: MSG=Socket timeout. IPADDRESS=%s SOCKTIME=%d

Message Level:: E

E0007044: MSG=Socket timeout. IPADDRESS=%s SOCKTIME=%d

Message Level:: E

E0007045: MSG=Socket timeout. IPADDRESS=%s SOCKTIME=%d

Message Level:: E

E0007046: MSG=Socket timeout. IPADDRESS=%s SOCKTIME=%d

Message Level:: E

E0007047: MSG=Socket timeout. IPADDRESS=%s SOCKTIME=%d

Message Level:: E

E0007048: MSG=Socket timeout. IPADDRESS=%s SOCKTIME=%d

Message Level:: E

E0007049: MSG=Socket timeout. IPADDRESS=%s SOCKTIME=%d

Message Level:: E

E0007050: MSG=Socket timeout. IPADDRESS=%s SOCKTIME=%d

Message Level:: E

E0008001: MSG=Socket read error. IPADDRESS=%s STRERROR=%s

Message Level:: E

Measure:: There may be problems in the socket stream. Check the environment. Also, check that it is not disconnected forcibly.

E0008002: MSG=Socket read error. IPADDRESS=%s STRERROR=%s

Message Level:: E

Measure:: There may be problems in the socket stream. Check the environment. Also, check that it is not disconnected forcibly.

E0008003: MSG=Memory allocate error. STRERROR=%s

Message Level:: E

Measure:: Check the environment. Terminate any unnecessary applications when the memory is insufficient.

E0008004: MSG=Socket read error. IPADDRESS=%s STRERROR=%s

Message Level:: E

Measure:: There may be problems in the socket stream. Check the environment. Also, check that it is not disconnected forcibly.

E0010001: MSG=Process fork error. STRERROR=%s

Message Level:: E

Measure:: Check the memory usage and the number of processes.

E0011001: MSG=Socket create error. STRERROR=%s

Message Level:: E

Measure:: Check that the specified host name and port number are correct.

E0011002: MSG=Socket option error. STRERROR=%s

Message Level:: E

E0011003: MSG=Socket option error. STRERROR=%s

Message Level:: E

E0011004: MSG=Socket create error. STRERROR=%s

Message Level:: E

Measure:: Check that the specified host name and port number are correct.

E0011005: MSG=Socket create error. STRERROR=%s

Message Level:: E

Measure:: Check that the specified host name and port number are correct.

E0011007: MSG=Socket option error. STRERROR=%s

Message Level:: E

E0011008: MSG=Socket option error. STRERROR=%s

Message Level:: E

E0011009: MSG=Socket option error. STRERROR=%s

Message Level:: E

E0011010: MSG=Socket create error. STRERROR=%s

Message Level:: E

Measure:: Check that the specified host name and port number are correct.

E0011011: MSG=Socket connect error. STRERROR=%s

Message Level:: E

Measure:: Check the network environment. Then, check that the specified host name and port number are correct.

E0011012: MSG=Socket option error. STRERROR=%s

Message Level:: E

E0011013: MSG=Socket option error. STRERROR=%s

Message Level:: E

E0011014: MSG=Socket option error. STRERROR=%s

Message Level:: E

E0011017: MSG=Socket option error. STRERROR=%s

Message Level:: E

E0011022: MSG=Process fork error. STRERROR=%s

Message Level:: E

Measure:: Check the memory usage and the number of processes.

E0011023: MSG=Failed to acquire the maximum value of SNDSOCKSIZE from the operating system.

Message Level:: E

E0011024: MSG=Failed to acquire the maximum value of RCVSOCKSIZE from the operating system.

Message Level:: E

E0011026: MSG=Length of path for UNIX domain socket exceeds the limit specified in the operating system. FILENAME=%s

Message Level:: E

E0011027: MSG=Length of path for UNIX domain socket exceeds the limit specified in the operating system. FILENAME=%s

Message Level:: E

E0012001: MSG=Socket create error. STRERROR=%s

Message Level:: E

Measure:: Check the network environment. Then, check that the specified host name and port number are correct.

E0012002: MSG=Socket option error. STRERROR=%s

Message Level:: E

E0012003: MSG=Socket connect error. STRERROR=%s

Message Level:: E

Measure:: Check the network environment. Then, check that the specified host name and port number are correct.

E0012004: MSG=Socket option error. STRERROR=%s

Message Level:: E

E0012005: MSG=Socket option error. STRERROR=%s

Message Level:: E

E0013001: MSG=Process fork error. STRERROR=%s

Message Level:: E

Measure:: Check the memory usage and the number of processes.

E0013010: MSG=Process fork error. STRERROR=%s

Message Level:: E

Measure:: Check the memory usage and the number of processes.

E0015001: MSG=File open error. FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E0015002: MSG=File lock error. FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E0016002: MSG=Memory allocate error. STRERROR=%s

Message Level:: E

Measure:: Check the environment. Terminate any unnecessary applications when the memory is insufficient.

E0016004: MSG=Value not set. PARAM=%s

Message Level:: E

Measure:: Check that a value is set to the tag in the System Environment Settings file (hulenv.conf).

E0016006: MSG=Tag not found. PARAM=%s

Message Level:: E

Measure:: Check that the tag is correctly set in the System Environment Settings file (hulenv.conf).

E0016008: MSG=Token '=' not found. PARAM=%s

Message Level:: E

Measure:: Check that the equal sign '=' is set in the tag in the System Environment Settings file (hulenv.conf).

E0016010: MSG=Range error. PARAM=%s VALUE=%s

Message Level:: E

Measure:: Check that the values set to the tags in the System Environment Settings file (hulenv.conf) are within the setting range.

E0016012: MSG=Path error. PARAM=%s VALUE=%s

Message Level:: E

Measure:: Check that the path set to the tag in the System Environment Settings file (hulenv.conf) is correct.

E0016014: MSG=String too long. PARAM=%s VALUE=%s

Message Level:: E

Measure:: Check that the value set to the tag in the System Environment Settings file (hulenv.conf) does not exceed the settable string length.

E0016016: MSG=Invalid value. PARAM=%s VALUE=%s

Message Level:: E

Measure:: Check that the available values are correctly described in the System Environment Settings file (hulenv.conf).

E0017001: MSG=Log file lock error. FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E0017002: MSG=Log file move error. FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E0017003: MSG=Memory allocate error. STRERROR=%s

Message Level:: E

Measure:: Check the environment. Terminate any unnecessary applications when the memory is insufficient.

E0017004: MSG=Log file open error. FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E0017005: MSG=Log file seek error. FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E0017006: MSG=Log file seek error. FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E0017007: MSG=Log file truncate error. FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E0017008: MSG=Log file write error. FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E0018001: MSG=Error occurred when requesting to agent(agent not exist).

Message Level:: E

E0018002: MSG=Error occurred when requesting to agent(response status=%d).

Message Level:: E

I3002002: MSG=Add send queue. FILEID=%s

Message Level:: I

I3008001: MSG=hulsndd end.

Message Level:: I

I3008005: MSG=hulsndd end.

Message Level:: I

I3011001: MSG=hulsndd start.

Message Level:: I

I3011002: MSG=hulsndd start (from hulclustersnd -endwait).

Message Level:: I

I3011003: MSG=hulsndd start (from hulclustersnd).

Message Level:: I

I3011006: MSG=hulsndd end.

Message Level:: I

I3013002: MSG=The Send processing that was forcibly terminated last time has been added to the Resend Queue. FILEID=%s HOSTNAME=%s

Message Level:: I

I3013009: MSG=Delete information on the resend queue file.

Message Level:: I

I3013010: MSG=Delete information on the resend status file.

Message Level:: I

I3015001: REQUEST=Send FILEID=%s

Message Level:: I

I3015002: REQUEST=Resend with checkpoint FILEID=%s

Message Level:: I

I3015003: REQUEST=Send (from obs) FILEID=%s

Message Level:: I

I3015004: REQUEST=Resend with checkpoint (from obs) FILEID=%s

Message Level:: I

I3015005: REQUEST=Unsending queue delete FILEID=%s

Message Level:: I

I3015006: REQUEST=Resend FILEID=%s

Message Level:: I

I3015007: REQUEST=Resend (from obs) FILEID=%s

Message Level:: I

I3015008: REQUEST=Resend record delete FILEID=%s

Message Level:: I

I3015009: REQUEST=Queue delete FILEID=%s TRID=%s

Message Level:: I

I3015010: REQUEST=Queue change FILEID=%s HOSTNAME=%s PRIORITY=%d

Message Level:: I

I3015012: REQUEST=Exit daemon TYPE=term exit

Message Level:: I

I3015013: REQUEST=Exit daemon TYPE=force exit

Message Level:: I

I3015014: REQUEST=System environment query TYPE=Query All FILENAME=%s

Message Level:: I

I3015015: REQUEST=System environment query TYPE=Query enable set only FILENAME=%s

Message Level:: I

I3015016: REQUEST=System environment resetting FILENAME=%s

Message Level:: I

I3015017: REQUEST=Exit daemon (from hulclustersnd) TYPE=term exit

Message Level:: I

I3015018: REQUEST=Exit daemon (from hulclustersnd) TYPE=force exit

Message Level:: I

I3015019: REQUEST=Alive check

Message Level:: I

I3015020: REQUEST=Send (from HULADMIN) FILEID=%s

Message Level:: I

I3015021: REQUEST=Resend with checkpoint (from HULADMIN) FILEID=%s

Message Level:: I

I3015022: REQUEST=Resend (from HULADMIN) FILEID=%s

Message Level:: I

I3015023: REPLY=Send (from HULADMIN)

Message Level:: I

I3015025: REPLY=Resend with checkpoint (from HULADMIN)

Message Level:: I

I3015027: REPLY=Resend (from HULADMIN)

Message Level:: I

I3015029: REPLY=Send

Message Level:: I

I3015031: REPLY=Resend with checkpoint

Message Level:: I

I3015033: REPLY=Send (from obs)

Message Level:: I

I3015035: REPLY=Resend with checkpoint (from obs)

Message Level:: I

I3015037: REPLY=Queue delete

Message Level:: I

I3015039: REPLY=Queue change

Message Level:: I

I3015041: REPLY=Unsending queue delete

Message Level:: I

I3015045: REPLY=Exit daemon

Message Level:: I

I3015047: REPLY=Resend

Message Level:: I

I3015049: REPLY=Resend (from obs)

Message Level:: I

I3015051: REPLY=Resend record delete

Message Level:: I

I3015053: REPLY=Alive check

Message Level:: I

I3015055: REPLY=System environment query

Message Level:: I

I3015057: REPLY=System environment resetting

Message Level:: I

I3015059: REPLY=Exit daemon (from hulclustersnd)

Message Level:: I

I3019003: MSG=Transfer Unit is calculated based on Maximum Segment Size (TCP_MAXSEG). MSS=%d TRANSUNIT=%d

Message Level:: I

I3021006: MSG=Autoretry resend wait. RETRYTIME=%d FILEID=%s HOSTNAME=%s

Message Level:: I

I3021007: MSG=Send end. FILEID=%s HOSTNAME=%s FILENAME=%s STS=%hd STSMSG=%s DSTS=%hd DSTSMSG=%s

Message Level:: I

I3021009: MSG=Autoretry resend cancel. FILEID=%s HOSTNAME=%s

Message Level:: I

I3021010: MSG=Unlock networked send file. FILEID=%s FILENAME=%s

Message Level:: I

I3021012: MSG=Transfer in Test-run Mode is complete. FILEID=%s, TTMODE=%d TTRCVOMIT=%d TTSNDJOB=%d TTSNDRCVLOG=%d

Message Level:: I

I3024002: MSG=Send start. FILEID=%s HOSTNAME=%s FILENAME=%s TRANSTYPE=%c

Message Level:: I

I3024008: MSG=Lock networked send file. FILEID=%s FILENAME=%s

Message Level:: I

I3024012: MSG=Performed autoconfiguration of the EBCDIC Set. EBCDICSET=%c

Message Level:: I

I3025001: MSG=HULFT retries connection using HULFT7 communication mode, because the remote host is in a lower version of HULFT. VERSION=%d FILEID=%s

Message Level:: I

I3025006: MSG=Checking transfer operation in Test-run Mode will start. FILEID=%s, TTMODE=%d TTRCVOMIT=%d TTSNDJOB=%d TTSNDRCVLOG=%d

Message Level:: I

I3025008: MSG=Checking transfer operation in Test-run Mode will start. FILEID=%s, TTMODE=%d TTRCVOMIT=%d TTSNDJOB=%d TTSNDRCVLOG=%d

Message Level:: I

I3027002: MSG=HULFT transfers file without compression, because the specified option for the Compression Preference cannot be used with HULFT7 Communication Mode. FILEID=%s

Message Level:: I

I3027003: MSG=Although the receiving host is HULFT ver.8 or higher, HULFT7 communication mode is used. FILEID=%s

Message Level:: I

I3027005: MSG=HULFT transfers the file without compression, because the receiving host does not support the specified option for the Compression Preference. FILEID=%s

Message Level:: I

I3028006: MSG=SAN(FAL) Verify check start FILEID=%s HOSTNAME=%s

Message Level:: I

I3028014: MSG=SAN(FAL) Verify check end FILEID=%s HOSTNAME=%s

Message Level:: I

I3028016: MSG=SAN(FAL) Verify check start FILEID=%s HOSTNAME=%s

Message Level:: I

I3028025: MSG=SAN(FAL) Verify check end FILEID=%s HOSTNAME=%s

Message Level:: I

I3028027: MSG=SAN(FAL) Verify check start FILEID=%s HOSTNAME=%s

Message Level:: I

I3028036: MSG=SAN(FAL) Verify check end FILEID=%s HOSTNAME=%s

Message Level:: I

I3028038: MSG=SAN(FAL) Verify check start FILEID=%s HOSTNAME=%s

Message Level:: I

I3028048: MSG=SAN(FAL) Verify check end FILEID=%s HOSTNAME=%s

Message Level:: I

I3030001: MSG=HULFT transfers the file without compression, because the receiving host does not support the specified option for the Compression Preference.

Message Level:: I

I3030002: MSG=Checking transfer operation in Test-run Mode will start. FILEID=%s, TTMODE=%d TTRCVOMIT=%d TTSNDJOB=%d TTSNDRCVLOG=%d

Message Level:: I

I3030004: MSG=File transferred with DEFLATE compression, because the receiving host does not support the specified option for Compression Preference.

Message Level:: I

I3030005: MSG=File transferred with Zstandard compression, because the receiving host does not support the specified option for Compression Preference.

Message Level:: I

I3032019: MSG=Speed priority mode cannot be used.

Message Level:: I

Measure:: Unable to use the Transfer Speed Priority Mode. Check the Framed Message Transfer Type and the version of the receiving host.

W3003001: MSG=Send queue is not found. FILEID=%s HOSTNAME=%s

Message Level:: W

W3005003: MSG=Autoretry resend. RETRYCNT=%d FILEID=%s HOSTNAME=%s

Message Level:: W

W3005004: MSG=Delete send queue. FILEID=%s HOSTNAME=%s

Message Level:: W

W3010013: MSG=A plug-in that cannot be used was detected. FILENAME=%s STRERROR=%s

Message Level:: W

W3010014: MSG=A plug-in that cannot be used was detected. FILENAME=%s

Message Level:: W

W3010015: MSG=A plug-in version that cannot be used was detected. FILENAME=%s

Message Level:: W

W3010016: MSG=The plug-in cannot be used, because you do not have a license for the Cloud Storage Option. FILENAME=%s

Message Level:: W

W3010017: MSG=The plug-in cannot be used, because the initialization of the plug-in that was loaded failed. FILENAME=%s PLUGINERR=%d DETAIL=%s

Message Level:: W

W3010018: MSG=The termination processing of the plug-in that was loaded failed. FILENAME=%s PLUGINERR=%d DETAIL=%s

Message Level:: W

W3010019: MSG=The plug-in cannot be used, because the directory could not be created during the initialization of the plug-in. FILENAME=%s STRERROR=%s

Message Level:: W

W3010020: MSG=The plug-in that supports this option is not installed. To use the option function, install the plug-in in the HULFT installation folder. OPTIONNAME=%s

Message Level:: W

W3012001: MSG=Delete send queue. FILEID=%s HOSTNAME=%s

Message Level:: W

W3017001: MSG=File information does not match the file information at the receiving side. Start transfer from the beginning.

Message Level:: W

W3018003: MSG=File transferred with HULFT Encryption Scheme, because HULFT Cipher Option (AES) is not installed on the receiving host. FILEID=%s

Message Level:: W

W3019006: MSG=Socket connect error. RETRYCNT=%d RETRYTIME=%d FILEID=%s HOSTNAME=%s

Message Level:: W

W3019007: MSG=An error occurred because the number of connections exceeded the maximum. RETRYCNT=%d RETRYTIME=%d FILEID=%s HOSTNAME=%s

Message Level:: W

W3020004: MSG=The code converting side has been switched to the receiving host because the sending host does not implement the code conversion between the specified encoding schemes. The result of the code conversion now depends on the settings on the receiving side.

Message Level:: W

W3021001: MSG=Send file truncate error. FILENAME=%s FILEID=%s STRERROR=%s

Message Level:: W

W3021002: MSG=Send file remove error. FILENAME=%s FILEID=%s STRERROR=%s

Message Level:: W

W3021005: MSG=Send end. FILEID=%s HOSTNAME=%s FILENAME=%s STS=%hd STSMSG=%s DSTS=%hd DSTSMSG=%s

Message Level:: W

W3021011: MSG=Failed to unlock networked send file. FILEID=%s FILENAME=%s

Message Level:: W

W3021013: MSG=Transfer in Test-run Mode was terminated unsuccessfully. FILEID=%s, TTMODE=%d TTRCVOMIT=%d TTSNDJOB=%d TTSNDRCVLOG=%d STS=%hd STSMSG=%s DSTS=%hd DSTSMSG=%s

Message Level:: W

W3021015: MSG=Failed to delete and make the Send file unrecoverable. FILENAME=%s FILEID=%s STRERROR=%s

Message Level:: W

W3021017: MSG=Failed to delete and make the Send file unrecoverable. FILENAME=%s FILEID=%s STRERROR=%s

Message Level:: W

Measure:: Check the error code returned from the operating system, and take measures.

W3024003: MSG=Failed in setting of the Exclusive Control file deletion processing. FILEID=%s STRERROR=%s

Message Level:: W

W3024010: MSG=Failed in the deletion processing of the Exclusive Control file.

Message Level:: W

W3024018: MSG=A plug-in that cannot be used was detected. FILENAME=%s STRERROR=%s

Message Level:: W

W3024019: MSG=A plug-in that cannot be used was detected. FILENAME=%s

Message Level:: W

W3024020: MSG=A plug-in version that cannot be used was detected. FILENAME=%s

Message Level:: W

W3024021: MSG=The plug-in cannot be used, because you do not have a license for the Cloud Storage Option. FILENAME=%s

Message Level:: W

W3024022: MSG=The plug-in cannot be used, because the initialization of the plug-in that was loaded failed. FILENAME=%s PLUGINERR=%d DETAIL=%s

Message Level:: W

W3024023: MSG=The termination processing of the plug-in that was loaded failed. FILENAME=%s PLUGINERR=%d DETAIL=%s

Message Level:: W

W3024024: MSG=The plug-in cannot be used, because the directory could not be created during the initialization of the plug-in. FILENAME=%s STRERROR=%s

Message Level:: W

W3025007: MSG=HULFT7 communication mode is not available, when you transfer in Test-run Mode. FILEID=%s, VERSION=%02d TTMODE=%d TTRCVOMIT=%d TTSNDJOB=%d TTSNDRCVLOG=%d

Message Level:: W

W3025009: MSG=HULFT7 communication mode is not available, when you transfer in Test-run Mode. FILEID=%s, VERSION=%02d TTMODE=%d TTRCVOMIT=%d TTSNDJOB=%d TTSNDRCVLOG=%d

Message Level:: W

W3026001: MSG=The specification for the following parameters is disabled, because the remote host does not support the Long Message. PARAM=%s VALUE=%s VERSION=%d

Message Level:: W

W3028002: MSG=SAN(FAL) Cannot load shared-library. STRERROR=%s

Message Level:: W

W3028003: MSG=SAN(FAL) Dataset open error. API-STS=%d VSN=%s DSN=%s

Message Level:: W

W3030003: MSG=The code converting side has been switched to the sending host because the receiving host does not implement the code conversion between the specified encoding schemes. The result of the code conversion now depends on the settings on the sending side.

Message Level:: W

W3032018: MSG=Change to LAN Transfer

Message Level:: W

W3037002: MSG=The request was not issued, because DataSpider Servista had not started.

Message Level:: W

W3038004: MSG=A warning message was output during the termination processing after the reading of the sending data. Close warning. DETAIL=%s

Message Level:: W

E3001001: MSG=Memory allocate error. STRERROR=%s

Message Level:: E

Measure:: Check the environment. Terminate any unnecessary applications when the memory is insufficient.

E3001002: MSG=Memory allocate error. STRERROR=%s

Message Level:: E

Measure:: Check the environment. Terminate any unnecessary applications when the memory is insufficient.

E3001003: MSG=Write unsendfile error. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3002001: MSG=Memory allocate error. STRERROR=%s

Message Level:: E

Measure:: Check the environment. Terminate any unnecessary applications when the memory is insufficient.

E3004001: MSG=Memory allocate error. STRERROR=%s

Message Level:: E

Measure:: Check the environment. Terminate any unnecessary applications when the memory is insufficient.

E3005001: MSG=Observe send error (SYNC: Client already exited).

Message Level:: E

E3005002: MSG=Observe send error (SYNC). STRERROR=%s

Message Level:: E

E3006001: MSG=Process fork error. STRERROR=%s

Message Level:: E

Measure:: Check the memory usage and the number of processes.

E3007001: MSG=Send management information is not found. FILEID=%s

Message Level:: E

Measure:: Check that the relevant record is registered in the Send Management Information.

E3007002: MSG=Message replace error. FILEID=%s FMTID=%s

Message Level:: E

Measure:: Check the contents of the message and the field to be replaced. Check the length of the replaced message does not exceed the field length limit.

E3007003: MSG=Message replace error. FILEID=%s JOBID=%s

Message Level:: E

Measure:: Check the contents of the message and the field to be replaced. Check the length of the replaced message does not exceed the field length limit.

E3007004: MSG=Message replace error. FILEID=%s JOBID=%s

Message Level:: E

Measure:: Check the contents of the message and the field to be replaced. Check the length of the replaced message does not exceed the field length limit.

E3007006: MSG=Message replace error. FILEID=%s FILENAME=%s

Message Level:: E

Measure:: Check the contents of the message and the field to be replaced. Check the length of the replaced message does not exceed the field length limit.

E3007007: MSG=Message replace error. FILEID=%s TGRPID=%s

Message Level:: E

Measure:: Check the contents of the message and the field to be replaced. Check the length of the replaced message does not exceed the field length limit.

E3007008: MSG=Host information registered in the Transfer Group Information is not found. TGRPID=%s

Message Level:: E

Measure:: Check that the host registered in the Transfer Group Information is registered in the Host Information.

E3008002: MSG=Socket read error. IPADDRESS=%s STRERROR=%s

Message Level:: E

Measure:: There may be problems in the socket stream. Check the environment. Also, check that it is not disconnected forcibly.

E3008003: MSG=Socket read error. IPADDRESS=%s

Message Level:: E

E3008004: MSG=Socket read size error. IPADDRESS=%s DATASIZE=%d/%d

Message Level:: E

E3009001: MSG=Host Information file read error. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3010001: MSG=Send status file open error. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3010002: MSG=Process fork error. STRERROR=%s

Message Level:: E

Measure:: Check the memory usage and the number of processes.

E3010003: MSG=Memory allocate error. STRERROR=%s

Message Level:: E

Measure:: Check the environment. Terminate any unnecessary applications when the memory is insufficient.

E3010004: MSG=hulsndd daemon already exists.

Message Level:: E

Measure:: Check that the Send daemon is already started with the ps command. Also, check the permission of the Send Control file (sddsendlist.dat).

E3010005: MSG=Send daemon pid file lock error. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system and take measures. Also, check the permission of the directory set to the Pid File Generation Path (piddir) in the System Environment Settings.

E3010008: MSG=Send daemon pid file write error. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3010009: MSG=hulsndd daemon already exists.

Message Level:: E

Measure:: Check that the Send daemon is already started with the ps command. Also, check the permission of the Send Control file (sddsendlist.dat).

E3010010: MSG=Send daemon pid file open error. FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system and take measures. Also, check the permission of the directory set to the Pid File Generation Path (piddir) in the System Environment Settings.

E3010011: MSG=hulsndd end. SIGNUM=%d

Message Level:: E

E3010012: MSG=Send daemon pid file delete error. FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3011005: MSG=hulsndd end.

Message Level:: E

E3013001: MSG=Send status file read error. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3013003: MSG=Send status file read error. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3013004: MSG=Send status file write error. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3013005: MSG=Send status file read error. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3013006: MSG=Send status file truncate error. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3013007: MSG=Send status file open error. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3013008: MSG=Send status file read error. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3013011: MSG=Send status file read error. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3013012: MSG=Send status file truncate error. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3014001: MSG=Memory allocate error. STRERROR=%s

Message Level:: E

Measure:: Check the environment. Terminate any unnecessary applications when the memory is insufficient.

E3015024: REPLY=Send (from HULADMIN) CMDSTS=%d

Message Level:: E

E3015026: REPLY=Resend with checkpoint (from HULADMIN) CMDSTS=%d

Message Level:: E

E3015028: REPLY=Resend (from HULADMIN) CMDSTS=%d

Message Level:: E

E3015030: REPLY=Send CMDSTS=%d

Message Level:: E

E3015032: REPLY=Resend with checkpoint CMDSTS=%d

Message Level:: E

E3015034: REPLY=Send (from obs) CMDSTS=%d

Message Level:: E

E3015036: REPLY=Resend with checkpoint (from obs) CMDSTS=%d

Message Level:: E

E3015038: REPLY=Queue delete CMDSTS=%d

Message Level:: E

E3015040: REPLY=Queue change CMDSTS=%d

Message Level:: E

E3015042: REPLY=Unsending queue delete CMDSTS=%d

Message Level:: E

E3015046: REPLY=Exit daemon CMDSTS=%d

Message Level:: E

E3015048: REPLY=Resend CMDSTS=%d

Message Level:: E

E3015050: REPLY=Resend (from obs) CMDSTS=%d

Message Level:: E

E3015052: REPLY=Resend record delete CMDSTS=%d

Message Level:: E

E3015054: REPLY=Alive check CMDSTS=%d

Message Level:: E

E3015056: REPLY=System environment query CMDSTS=%d

Message Level:: E

E3015058: REPLY=System environment resetting CMDSTS=%d

Message Level:: E

E3015060: REPLY=Exit daemon (from hulclustersnd) CMDSTS=%d

Message Level:: E

E3016001: MSG=Observe send error (Client already exited).

Message Level:: E

E3018001: MSG=Failed in the initialization of the encryption exit routine. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3018002: MSG=Unable to transfer the file because Forced Strong Key mode is off on the remote host. Enabling Forced Strong Key mode is required on both side. FILEID=%s HOSTNAME=%s

Message Level:: E

Measure:

Check either of the following conditions are met:

The remote host runs HULFT lower than Ver.8.4.
The product of the remote host is a No Encryption.
Forced Strong Key mode on the remote host is off.

E3019001: MSG=Retry count exceeded. FILEID=%s RETRYCNT=%d HOSTNAME=%s

Message Level:: E

E3019002: MSG=Socket option error. STRERROR=%s

Message Level:: E

E3019004: MSG=Send status file write error. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3019005: MSG=Send status file write error. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3020001: MSG=Format convert error. FILEID=%s FMTID=%s ITEMTYPE=%c

Message Level:: E

Measure:: Check that the Format Information is correctly set.

E3020002: MSG=Format convert error. FILEID=%s FMTID=%s ITEMTYPE=%c

Message Level:: E

Measure:: Check that the Format Information is correctly set.

E3020003: MSG=Format convert error. FILEID=%s FMTID=%s ITEMTYPE=%c

Message Level:: E

Measure:: Check that the Format Information is correctly set.

E3021003: MSG=Send status file write error. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3021004: MSG=Process fork error. STRERROR=%s

Message Level:: E

Measure:: Check the memory usage and the number of processes.

E3021008: MSG=Send end. FILEID=%s HOSTNAME=%s FILENAME=%s STS=%hd STSMSG=%s DSTS=%hd DSTSMSG=%s

Message Level:: E

E3021014: MSG=Send file delete error. FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3021016: MSG=Failed to delete and make the Send file unrecoverable. FILENAME=%s STRERROR=%s

Message Level:: E

E3023001: MSG=Socket option error. STRERROR=%s

Message Level:: E

E3024001: MSG=Send status file read error. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3024004: MSG=Send file size error. FILEID=%s FILENAME=%s

Message Level:: E

E3024005: MSG=Send file open error. FILEID=%s FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3024006: MSG=Send file open error. FILEID=%s FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3024007: MSG=Failed to lock networked send file. FILEID=%s FILENAME=%s

Message Level:: E

E3024009: MSG=Send file open error. FILEID=%s FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3024011: MSG=Combination Error of the Code Set for Transfer. MYCODESET=%c YOURCODESET=%c

Message Level:: E

Measure 1:: For regular transfer, check that the following combination of code sets are supported: (a) the remote host's code set specified as Code Set for Transfer (KCODETYPE) in the Host Information, and (b) the code set specified as Code Set for Transfer (cs4trnsfr) in the System Environment Settings.
Measure 2:: For instant transfer, check that the combination of the code sets that are specified as Code Set for Transfer (cs4trnsfr) in the System Environment Settings on the remote host and the local host is supported.

E3024013: MSG=Combination Error with EBCDIC Set. CS4TRNSFR=%c EBCDICSET=%c

Message Level:: E

Measure 1:: For regular transfer, check that the combination of values specified for the following fields is supported: (a) Code Set for Transfer (KCODETYPE) in the Host Information, and (b) EBCDIC Set in the Send or Receive Management Information.
Measure 2:: For instant transfer, check that the combination of values specified for the following fields in the System Environment Settings on the remote host is supported: (a) Code Set for Transfer (cs4trnsfr) and (b) Instant Transfer EBCDIC Set. Also, make sure that the version of HULFT on the local host is a version in which code conversion from/to the code set specified as Instant Transfer EBCDIC Set in the System Environment Settings on the remote host is supported.

E3024017: MSG=Inconsistency is found between Forced Strong Key mode set in the System Environment Settings and the length of the cipher key specified in management information. FILEID=%s HOSTNAME=%s

Message Level:: E

Measure:

If Forced Strong Key mode is enabled, use a cipher key of 64 digits hexadecimal character string.

If Forced Strong Key mode is disabled, use a cipher key of 0 or 8 to 20 bytes alphanumeric character string.

E3024025: MSG=If a file name that includes "://" is specified in Error Handling, only "K" (Keep) can be specified in Send File Mode. FILEID=%s

Message Level:: E

E3025002: MSG=An error occurred because the number of connections exceeded the maximum. FILEID=%s HOSTNAME=%s

Message Level:: E

Measure:: Increase the value of Receive Process Multiplex Level of the receiving host, or wait for a while and then transfer again.

E3025003: MSG=Failed in the termination of the encryption exit routine. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3025004: MSG=Send status file write error. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3025005: MSG=Received data is broken.

Message Level:: E

E3025010: MSG=Received data is broken.

Message Level:: E

E3025011: MSG=The instant transfer will be terminated because the product version of the receiving host is not a version that can perform an instant transfer. HOSTNAME=%s

Message Level:: E

Measure:

Perform either of the following:

Check whether the version running on the remote host supports instant transfer.
The file transfer fails if File ID is set to "_INSTANT_TRANSFER_". Use a different ID if that is the case.

E3025012: MSG=Unable to transfer the file because Use HULFT7 Comm. mode is enabled in the Host Information. To use Forced Strong Key mode, disable Use HULFT7 Comm. mode. FILEID=%s HOSTNAME=%s

Message Level:: E

Measure:

Check either of the following conditions are met:

The remote host runs HULFT lower than Ver.8.4.
The product of the remote host is a No Encryption.
Forced Strong Key mode on the remote host is off.

E3025013: MSG=Unable to transfer the file because Forced Strong Key mode is off on the remote host. Enabling Forced Strong Key mode is required on both side. FILEID=%s HOSTNAME=%s

Message Level:: E

Measure:

Check either of the following conditions are met:

The remote host runs HULFT lower than Ver.8.4.
The product of the remote host is a No Encryption.
Forced Strong Key mode on the remote host is off.

E3025014: MSG=The instant transfer will be terminated because the product version of the receiving host is not a version that can perform an instant transfer. FILEID=%s HOSTNAME=%s

Message Level:: E

Measure:

Perform either of the following:

Check whether the version running on the remote host supports instant transfer.
The file transfer fails if File ID is set to "_INSTANT_TRANSFER_". Use a different ID if that is the case.

E3027001: MSG=An error occurred because the number of connections exceeded the maximum. FILEID=%s HOSTNAME=%s

Message Level:: E

Measure:: Increase the value of Receive Process Multiplex Level of the receiving host, or wait for a while and then transfer again.

E3027004: MSG=Communication error. Unable to send the parameter to the remote host. The remote host is in a lower version of HULFT, which supports shorter parameter only. PARAM=%s VALUE=%s VERSION=%d

Message Level:: E

E3027006: MSG=Communication error. Unable to send the parameter to the remote host. The remote host is in a lower version of HULFT, which supports shorter parameter only. PARAM=%s VALUE=%s

Message Level:: E

E3029001: MSG=Unknown protocol.

Message Level:: E

Measure:: An error occurred while receiving the data, or incorrect data might have been received. Transfer the data again.

E3029002: MSG=Memory allocate error. STRERROR=%s

Message Level:: E

Measure:: Check the environment. Terminate any unnecessary applications when the memory is insufficient.

E3031001: MSG=Failed in the processing of the encryption exit routine. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3032001: MSG=Socket timeout. FILEID=%s HOSTNAME=%s SOCKTIME=%d

Message Level:: E

Measure:: Check that there is no line fault, and the value for Socket Timeout is sufficient.

E3032002: MSG=Sending host is LAN-Version. HOSTNAME=%s FILEID=%s STS=%d DSTS=%d

Message Level:: E

E3032003: MSG=Receiving HULFT version is Ver.4 or lower. HOSTNAME=%s FILEID=%s STS=%d DSTS=%d

Message Level:: E

E3032005: MSG=Receiving host is LAN-Version. HOSTNAME=%s FILEID=%s STS=%d DSTS=%d

Message Level:: E

E3032020: MSG=Failed in the processing of the encryption exit routine. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3032021: MSG=Failed in the processing of the DEFLATE routine.

Message Level:: E

E3032022: MSG=Failed in the processing of the DEFLATE routine.

Message Level:: E

E3032023: MSG=Send file seek error. FILEID=%s FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3032024: MSG=Send file read error. FILEID=%s FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3032025: MSG=Data length too long. FILEID=%s FILENAME=%s LENGTH=%d

Message Level:: E

Measure:: There is an error in the data size of the Send file. Check the Send file. In text transfer, the maximum byte size per record (one line before a linefeed) is 32768.

E3032026: MSG=Send file read error. FILEID=%s FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3032027: MSG=Custom character convert error. FILEID=%s FILENAME=%s

Message Level:: E

Measure:: Input data includes data that has not been registered in the custom character table. Register the data in the custom character table, or check the data contents.

E3032028: MSG=Code convert error. FILEID=%s FILENAME=%s

Message Level:: E

Measure:: Check Code Set for Transfer (cs4trnsfr) and Standard for Japanese (jistype) specified in the System Environment Settings and the settings of the receiving-side host specified as Code Set for Transfer (KCODETYPE) and Standard for Japanese (JISYEAR) in the Host Information.

E3032029: MSG=Data length too long. FILEID=%s FILENAME=%s LENGTH=%d

Message Level:: E

Measure:: There is an error in the data size of the Send file. Check the Send file. In text transfer, the maximum byte size per record (one line before a line break) is 32768.

E3032030: MSG=Send file read error. FILEID=%s FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3032031: MSG=Send file read error. FILEID=%s FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3032032: MSG=Send file read error. FILEID=%s FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3032033: MSG=Send file read error. FILEID=%s FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3032034: MSG=Format Information file open error. FILEID=%s FMTID=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3032035: MSG=Format Information is not found. FILEID=%s FMTID=%s

Message Level:: E

Measure:: Check that the Format Information is correctly registered.

E3032036: MSG=Socket timeout. FILEID=%s HOSTNAME=%s SOCKTIME=%d

Message Level:: E

Measure:: Check that there is no line fault, and the value for Socket Timeout is sufficient.

E3032037: MSG=Send status file write error. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3032038: MSG=Receiving host error. FILEID=%s HOSTNAME=%s STS=%d

Message Level:: E

Measure:: Check the error code in the Receive Log of the receiving host and take appropriate measures. Then, re-execute.

E3032039: MSG=Failed in the processing of the DEFLATE routine.

Message Level:: E

E3032040: MSG=Failed in the processing of the Zstandard routine.

Message Level:: E

E3032041: MSG=Failed in the processing of the Zstandard routine.

Message Level:: E

E3032042: MSG=Failed in the processing of the Zstandard routine.

Message Level:: E

E3034001: MSG=Multi Format Information file read error. FILEID=%s MFMTID=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3035001: MSG=Connect version error. VERSION=%6.6s

Message Level:: E

Measure:: The version of the product at the connection destination is not supported. Check the supported version.

E3035002: MSG=Proxy connect error. STS=%d DSTS=%d FILEID=%s HOSTNAME=%s

Message Level:: E

Measure:: HULFT-HUB Server has notified the error. As the error code of HULFT-HUB Server has been set in the Detail Code. Refer to the description of the error on the side of HULFT-HUB Server.

E3035003: MSG=Unknown protocol.

Message Level:: E

Measure:: An error occurred while receiving the data, or incorrect data might have been received. Transfer the data again.

E3036001: MSG=Send daemon pid file delete error. FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3037001: MSG=Failed to issue a request to DataSpider Servista. HTTPSTS=%d

Message Level:: E

Measure:: Check the HTTP status code and take measures.

E3037003: MSG=Failed to issue a request to DataSpider Servista.

Message Level:: E

Measure:: Check the setting of HULFT Script Port No.

E3037004: MSG=An error occurred while writing to the Send Log file. HOSTNAME=%s FILEID=%s STS=%d DSTS=%d STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E3038001: MSG=The initialization processing for reading the sending data failed. Open error. DETAIL=%s

Message Level:: E

E3038002: MSG=The read processing of the sending data failed. Read error. DETAIL=%s

Message Level:: E

E3038003: MSG=The termination processing executed after the reading of the sending data failed. Close error DETAIL=%s

Message Level:: E

I1001001: REQUEST=Exit daemon (from hulclusterrcv) TYPE=force exit

Message Level:: I

I1001002: REQUEST=Exit daemon (from hulclusterrcv) TYPE=term exit

Message Level:: I

I1001004: REPLY=Exit daemon (from hulclusterrcv)

Message Level:: I

I1001005: REQUEST=Exit daemon (from hulclusterrcv) TYPE=force exit

Message Level:: I

I1001006: MSG=hulrcvd end.

Message Level:: I

I1001009: REQUEST=Request message for cancelling receiving.

Message Level:: I

I1001010: REPLY=Request message for cancelling receiving. REQUESTED_COUNT=%d, CANCELED_COUNT=%d

Message Level:: I

I1002001: REQUEST=System environment resetting FILENAME=%s

Message Level:: I

I1002002: REPLY=System environment resetting

Message Level:: I

I1003001: REQUEST=System environment query TYPE=Query All FILENAME=%s

Message Level:: I

I1003002: REQUEST=System environment query TYPE=Query enable set only FILENAME=%s

Message Level:: I

I1003004: REPLY=System environment query

Message Level:: I

I1005003: MSG=Lock networked receive work file. FILEID=%s FILENAME=%s

Message Level:: I

I1005010: MSG=Lock networked receive backup file. FILEID=%s FILENAME=%s

Message Level:: I

I1005013: MSG=Lock networked receive file. FILEID=%s FILENAME=%s

Message Level:: I

I1005015: MSG=Unlock networked receive file. FILEID=%s FILENAME=%s

Message Level:: I

I1005017: MSG=Unlock networked receive work file. FILEID=%s FILENAME=%s

Message Level:: I

I1005019: MSG=Unlock networked receive backup file. FILEID=%s FILENAME=%s

Message Level:: I

I1006002: MSG=Recv end. FILEID=%s HOSTNAME=%s FILENAME=%s STS=%hd STSMSG=%s DSTS=%hd DSTSMSG=%s

Message Level:: I

I1006007: MSG=CSV exec start. FILEID=%s

Message Level:: I

I1006009: MSG=CSV exec end. FILEID=%s

Message Level:: I

I1006012: MSG=Transfer in Test-run Mode is complete. FILEID=%s, TTMODE=%d TTRCVFILOUTPUT=%d TTRCVJOB=%d TTSNDRCVLOG=%d

Message Level:: I

I1008001: REQUEST=Alive check

Message Level:: I

I1008002: REPLY=Alive check

Message Level:: I

I1010002: MSG=Recv start. FILEID=%s HOSTNAME=%s TRANSTYPE=%c IPADDRESS=%s VERSION=%02d

Message Level:: I

I1012007: MSG=Performed autoconfiguration of the EBCDIC Set. EBCDICSET=%c

Message Level:: I

I1013002: MSG=Recv start. FILEID=%s HOSTNAME=%s TRANSTYPE=%c IPADDRESS=%s VERSION=%02d

Message Level:: I

I1013014: MSG=Checking transfer operation in Test-run Mode will start. FILEID=%s, TTMODE=%d TTRCVFILOUTPUT=%d TTRCVJOB=%d TTSNDRCVLOG=%d

Message Level:: I

I1013016: MSG=Performed autoconfiguration of the EBCDIC Set. EBCDICSET=%c

Message Level:: I

I1013019: MSG=A Send File request (for instant transfer) has been accepted. The processing continues in accordance with the allowance/denial settings.

Message Level:: I

I1015003: MSG=hulrcvd start (from hulclusterrcv -endwait).

Message Level:: I

I1015004: MSG=hulrcvd start (from hulclusterrcv).

Message Level:: I

I1015005: MSG=hulrcvd start.

Message Level:: I

I1015007: REQUEST=Exit daemon

Message Level:: I

I1015008: REPLY=Exit daemon

Message Level:: I

I1015009: MSG=hulrcvd end.

Message Level:: I

W1005001: MSG=Failed in setting of the Exclusive Control file deletion processing. FILEID=%s STRERROR=%s

Message Level:: W

W1005016: MSG=Failed to unlock networked receive file. FILEID=%s FILENAME=%s

Message Level:: W

W1005018: MSG=Failed to unlock networked receive work file. FILEID=%s FILENAME=%s

Message Level:: W

W1005020: MSG=Failed to unlock networked receive backup file. FILEID=%s FILENAME=%s

Message Level:: W

W1005021: MSG=Failed in the deletion processing of the Exclusive Control file.

Message Level:: W

W1005022: MSG=Failed to unlink the receive generation temporary file. FILENAME=%s STRERROR=%s

Message Level:: W

W1005024: MSG=Failed to unlink the receive generation temporary file. FILENAME=%s STRERROR=%s

Message Level:: W

W1005025: MSG=Failed to move the Receive file. from=%s to=%s STRERROR=%s

Message Level:: W

W1005029: MSG=Failed to delete and make the backup file for restoring the Receive file unrecoverable. FILENAME=%s STRERROR=%s

Message Level:: W

Measure:: Check the error code returned from the operating system, and take measures.

W1005030: MSG=Failed to delete and make the backup file for restoring the Receive file unrecoverable. FILENAME=%s STRERROR=%s

Message Level:: W

Measure:: Check the error code returned from the operating system, and take measures.

W1005031: MSG=Failed to delete and make the generational management temporary file unrecoverable. FILENAME=%s STRERROR=%s

Message Level:: W

Measure:: Check the error code returned from the operating system, and take measures.

W1005032: MSG=Failed to delete and make the generational management temporary file unrecoverable. FILENAME=%s STRERROR=%s

Message Level:: W

Measure:: Check the error code returned from the operating system, and take measures.

W1006011: MSG=Transfer in Test-run Mode was terminated unsuccessfully. FILEID=%s, TTMODE=%d TTRCVFILOUTPUT=%d TTRCVJOB=%d TTSNDRCVLOG=%d STS=%hd STSMSG=%s DSTS=%hd DSTSMSG=%s

Message Level:: W

W1006013: MSG=Failed to unlink the receive generation temporary file. FILENAME=%s STRERROR=%s

Message Level:: W

W1006014: MSG=Failed to unlink the receive temporary file. FILENAME=%s STRERROR=%s

Message Level:: W

W1006015: MSG=Failed to unlink the receive temporary file. FILENAME=%s STRERROR=%s

Message Level:: W

W1006016: MSG=Failed to unlink the receive format file. FILENAME=%s STRERROR=%s

Message Level:: W

W1006017: MSG=Failed to unlink the receive file. FILENAME=%s STRERROR=%s

Message Level:: W

W1006018: MSG=Failed to unlink the receive file. FILENAME=%s STRERROR=%s

Message Level:: W

W1006019: MSG=Failed to move the Receive file. from=%s to=%s STRERROR=%s

Message Level:: W

W1006020: MSG=Failed to delete and make the backup file for restoring the Receive file unrecoverable. FILENAME=%s STRERROR=%s

Message Level:: W

W1006021: MSG=Failed to delete and make the Receive file unrecoverable. FILENAME=%s STRERROR=%s

Message Level:: W

W1006022: MSG=Failed to delete and make the Receive file unrecoverable. FILENAME=%s STRERROR=%s

Message Level:: W

W1006023: MSG=Failed to delete and make the temporary Receive file unrecoverable. FILENAME=%s STRERROR=%s

Message Level:: W

W1006024: MSG=Failed to delete and make the generational management temporary file unrecoverable. FILENAME=%s STRERROR=%s

Message Level:: W

W1007001: MSG=File information does not match the file information at the sending side. FILEID=%s FILENAME=%s

Message Level:: W

W1007002: MSG=Failed to get the state of receive file. FILEID=%s FILENAME=%s

Message Level:: W

W1011002: MSG=Change to LAN Transfer

Message Level:: W

W1011004: MSG=Change to LAN Transfer

Message Level:: W

W1011006: MSG=Change to LAN Transfer

Message Level:: W

W1011008: MSG=Change to LAN Transfer

Message Level:: W

W1012003: MSG=A cipher key is not set up. FILEID=%s

Message Level:: W

Measure:: Check that a value is set in Cipher Key (PASSWORD) in the Receive Management Information.

W1012005: MSG=HULFT7 communication mode is not available, when you transfer in Test-run Mode. FILEID=%s TTMODE=%d TTRCVFILOUTPUT=%d TTRCVJOB=%d TTSNDRCVLOG=%d

Message Level:: W

W1012009: MSG=File transferred without encryption, because no option is specified for Cipher Key on the sending host. FILEID=%s

Message Level:: W

W1012010: MSG=File transferred with HULFT Encryption Scheme, because HULFT Cipher Option (AES) is not installed on the sending host. FILEID=%s

Message Level:: W

W1013008: MSG=A cipher key is not set up. FILEID=%s

Message Level:: W

Measure:: Check that a value is set in Cipher Key (PASSWORD) in the Receive Management Information.

W1013026: MSG=File transferred without encryption, because no option is specified for Cipher Key on the sending host. FILEID=%s

Message Level:: W

W1013027: MSG=File transferred with HULFT Encryption Scheme, because HULFT Cipher Option (AES) is not installed on the sending host. FILEID=%s

Message Level:: W

W1016001: MSG=Change to LAN Transfer

Message Level:: W

W1020001: MSG=Failed to unlink the receive file. FILENAME=%s STRERROR=%s

Message Level:: W

W1020002: MSG=Failed to move the Receive file. from=%s to=%s STRERROR=%s

Message Level:: W

W1020003: MSG=Failed to unlink the receive file. FILENAME=%s STRERROR=%s

Message Level:: W

W1020004: MSG=Failed to unlink the receive file. FILENAME=%s STRERROR=%s

Message Level:: W

W1020005: MSG=Failed to secure delete the receive file. FILENAME=%s STRERROR=%s

Message Level:: W

W1020006: MSG=Failed to secure delete the receive file. FILENAME=%s STRERROR=%s

Message Level:: W

W1020007: MSG=Failed to secure delete the receive file. FILENAME=%s STRERROR=%s

Message Level:: W

W1020008: MSG=Failed to secure delete the receive file. FILENAME=%s STRERROR=%s

Message Level:: W

W1021002: MSG=The request was not issued, because DataSpider Servista had not started.

Message Level:: W

E1001003: MSG=Unknown protocol.

Message Level:: E

Measure:: An error occurred while receiving the data, or incorrect data might have been received. Transfer the data again.

E1001007: MSG=hulrcvd process received signal. PID=%d SIGNUM=%d

Message Level:: E

E1001008: MSG=hulrcvd process abnormal end. PID=%d

Message Level:: E

Measure:: Check log records in the Receive Log.

E1002003: REPLY=System environment resetting CMDSTS=%d

Message Level:: E

E1003003: REPLY=System environment query CMDSTS=%d

Message Level:: E

E1004001: MSG=Receive file size mismatch. FILEID=%s FILESIZE=%llu

Message Level:: E

Measure:: Check the contents and attributes of the Send file and the Receive file.

E1004002: MSG=Receive file record mismatch. FILEID=%s RECCNT=%llu

Message Level:: E

Measure:: Check the contents and attributes of the Send file and the Receive file.

E1005002: MSG=Failed to lock networked receive work file. FILEID=%s FILENAME=%s

Message Level:: E

E1005004: MSG=Receive file open error. FILEID=%s FILENAME=%s STRERROR=%s

Message Level:: E

E1005005: MSG=Receive work file fsync error. FILEID=%s FILENAME=%s STRERROR=%s

Message Level:: E

E1005006: MSG=Receive file fsync error. FILEID=%s FILENAME=%s STRERROR=%s

Message Level:: E

E1005007: MSG=Receive file fsync error. FILEID=%s FILENAME=%s STRERROR=%s

Message Level:: E

E1005008: MSG=Receive file open error. FILEID=%s FILENAME=%s STRERROR=%s

Message Level:: E

E1005009: MSG=Failed to lock networked receive backup file. FILEID=%s FILENAME=%s

Message Level:: E

E1005011: MSG=Receive file already exist. FILEID=%s FILENAME=%s

Message Level:: E

Measure:: Delete the file, or set Registration Mode to 'R: Replace' or 'M: Append' in the Receive Management Information.

E1005012: MSG=Failed to lock networked receive file. FILEID=%s FILENAME=%s

Message Level:: E

E1005014: MSG=Receive file lock error. FILEID=%s FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E1005023: MSG=Failed to move the Receive file. from=%s to=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E1005026: MSG=Failed to move the file. from=%s to=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E1005027: MSG=Failed to move the file. from=%s to=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E1005028: MSG=Failed to copy the file. from=%s to=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E1005033: MSG=Failed to delete and make the previously-created backup file for restoring the Receive file unrecoverable. FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E1005034: MSG=Failed to delete and make the previously-created Receive file managed in generations unrecoverable. FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E1005035: MSG=Failed to delete and make the previously-created backup file for restoring the Receive file unrecoverable. FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E1005036: MSG=Failed to delete and make the previously-created Receive file unrecoverable. FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E1006001: MSG=Recv end. FILEID=%s HOSTNAME=%s FILENAME=%s STS=%hd STSMSG=%s DSTS=%hd DSTSMSG=%s

Message Level:: E

E1006003: MSG=Failed in the termination of the encryption exit routine. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E1006004: MSG=Job timeout. FILEID=%s JOBID=%s

Message Level:: E

Measure:: Increase the setting of Job Timeout (jobwtimeout) in the System Environment Settings.

E1006005: MSG=Memory allocate error. FILEID=%s JOBID=%s STRERROR=%s

Message Level:: E

E1006006: MSG=Job exec end. FILEID=%s JOBID=%s JOBSTS=%d

Message Level:: E

E1006008: MSG=CSV exec error. FILEID=%s

Message Level:: E

Measure:: Check that the contents of the CSV Environment Settings file (hulcsv.info) and the Format Information are set correctly and that the data is correct.

E1006010: MSG=Socket read error. IPADDRESS=%s STRERROR=%s

Message Level:: E

Measure:: There may be problems in the socket stream. Check the environment. Also, check that it is not disconnected forcibly.

E1007003: MSG=Failed in the processing of the encryption exit routine. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E1008004: MSG=Unable to transfer the file because Forced Strong Key mode is off on the remote host. Enabling Forced Strong Key mode is required on both side. IPADDRESS=%s

Message Level:: E

Measure:

Check either of the following conditions are met:

The remote host runs HULFT lower than Ver.8.4.
The product of the remote host is a No Encryption.
Forced Strong Key mode on the remote host is off.

E1009001: MSG=Message replace error. FILEID=%s FILENAME=%s

Message Level:: E

Measure:: Check the contents of the message and the field to be replaced. Check the length of the replaced message does not exceed the field length limit.

E1009002: MSG=Message replace error. FILEID=%s TGRPID=%s

Message Level:: E

Measure:: Check the contents of the message and the field to be replaced. Check the length of the replaced message does not exceed the field length limit.

E1009003: MSG=Message replace error. FILEID=%s JOBID=%s

Message Level:: E

Measure:: Check the contents of the message and the field to be replaced. Check the length of the replaced message does not exceed the field length limit.

E1009004: MSG=Message replace error. FILEID=%s JOBID=%s

Message Level:: E

Measure:: Check the contents of the message and the field to be replaced. Check the length of the replaced message does not exceed the field length limit.

E1010001: MSG=An error occurred because the number of connections exceeded the maximum. STS=%d

Message Level:: E

Measure:: Increase the value of Receive Process Multiplex Level (rcvpsnum) in the System Environment Settings, or transfer again after a while.

E1010003: MSG=Receive status file open error. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E1010004: MSG=Unable to transfer the file because Forced Strong Key mode is off on the remote host. Enabling Forced Strong Key mode is required on both side. FILEID=%s

Message Level:: E

Measure:

Check either of the following conditions are met:

The remote host runs HULFT lower than Ver.8.4.
The product of the remote host is a No Encryption.
Forced Strong Key mode on the remote host is off.

E1011003: MSG=Cannot allocate memory. STRERROR=%s

Message Level:: E

E1011005: MSG=Cannot allocate memory. STRERROR=%s.

Message Level:: E

E1012001: MSG=Verify version error (less than 7). VERSION=%02d FILEID=%s HOSTNAME=%s

Message Level:: E

E1012002: MSG=Failed in the initialization of the encryption exit routine. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E1012004: MSG=Transfer group information is not found. FILEID=%s TGRPID=%s

Message Level:: E

Measure:: Check that the Transfer Group Information is correctly registered.

E1012006: MSG=Combination Error of the Code Set for Transfer. MYCODESET=%c YOURCODESET=%c

Message Level:: E

Measure 1:: For regular transfer, check that the following combination of code sets is supported: (a) the remote host's code set specified as Code Set for Transfer (KCODETYPE) in the Host Information, and (b) the code set specified as Code Set for Transfer (cs4trnsfr) in the System Environment Settings.
Measure 2:: For instant transfer, check that the combination of code sets specified as Code Set for Transfer (cs4trnsfr) in the System Environment Settings on the remote host and the local host is supported.

E1012008: MSG=Combination Error with EBCDIC Set. CS4TRNSFR=%c EBCDICSET=%c

Message Level:: E

Measure 1:

For regular transfer, check that the combination of values specified for the following fields is supported: (a) Code Set for Transfer (KCODETYPE) in the Host Information, and (b) EBCDIC Set in the Send or Receive Management Information.

Measure 2:

For instant transfer, check that the combination of values specified for the following fields in the System Environment Settings on the remote host is supported: (a) Code Set for Transfer (cs4trnsfr) and (b) Instant Transfer EBCDIC Set.

Also, make sure that the version of HULFT on the local host is a version in which code conversion from/to the code set specified as Instant Transfer EBCDIC Set in the System Environment Settings on the remote host is supported.

E1013001: MSG=An error occurred because the number of connections exceeded the maximum. STS=%d

Message Level:: E

Measure:: Increase the value of Receive Process Multiplex Level (rcvpsnum) in the System Environment Settings, or transfer again after a while.

E1013003: MSG=Received data is broken.

Message Level:: E

E1013004: MSG=Receive status file open error. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E1013005: MSG=Failed in the initialization of the DEFLATE routine.

Message Level:: E

E1013006: MSG=Failed in the initialization of the DEFLATE routine.

Message Level:: E

E1013007: MSG=Failed in the initialization of the encryption exit routine. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E1013010: MSG=Message replace error. FILEID=%s FILENAME=%s

Message Level:: E

Measure:: Check the contents of the message and the field to be replaced. Check the length of the replaced message does not exceed the field length limit.

E1013011: MSG=Message replace error. FILEID=%s TGRPID=%s

Message Level:: E

Measure:: Check the contents of the message and the field to be replaced. Check the length of the replaced message does not exceed the field length limit.

E1013012: MSG=Message replace error. FILEID=%s JOBID=%s

Message Level:: E

Measure:: Check the contents of the message and the field to be replaced. Check the length of the replaced message does not exceed the field length limit.

E1013013: MSG=Message replace error. FILEID=%s JOBID=%s

Message Level:: E

Measure:: Check the contents of the message and the field to be replaced. Check the length of the replaced message does not exceed the field length limit.

E1013015: MSG=Combination Error of the Code Set for Transfer. MYCODESET=%c YOURCODESET=%c

Message Level:: E

Measure 1:: For regular transfer, check that the following combination of code sets is supported: (a) the remote host's code set specified as Code Set for Transfer (KCODETYPE) in the Host Information, and (b) the code set specified as Code Set for Transfer (cs4trnsfr) in the System Environment Settings.
Measure 2:: For instant transfer, check that the combination of the code sets specified as Code Set for Transfer (cs4trnsfr) in the System Environment Settings on the remote and local hosts.

E1013017: MSG=Combination Error with EBCDIC Set. CS4TRNSFR=%c EBCDICSET=%c

Message Level:: E

Measure 1:

For regular transfer, check that the combination of code sets specified as the following fields is supported: (a) Code Set for Transfer (KCODETYPE) in the Host Information, and (b) EBCDIC Set in the Send or Receive Management Information.

Measure 2:

For instant transfer, check that the combination of code sets specified as the following fields in the System Environment Settings on the remote host is supported: (a) Code Set for Transfer (cs4trnsfr) and (b) Instant Transfer EBCDIC Set.

Also, make sure that the version of HULFT on the local host is a version in which code conversion from/to the code set specified as Instant Transfer EBCDIC Set in the System Environment Settings on the remote host.

E1013018: MSG=The instant transfer request from the sending host was denied during the receive processing. HOSTNAME=%s

Message Level:: E

Measure:

Check whether the request from the sending host is correct. If correct, take any of the following measures:

If the sending host is not registered in the Host Information, register its information.
If the sending host is registered in the Host Information, change the allowance/denial settings for the host in the Host Information.

E1013020: MSG=The instant transfer request from the sending host was denied during the receive processing. INSTTRANSROOT=%s, RCVLOC=%s

Message Level:: E

Measure:: Check that the request from the sending host is correct. If it is correct, then check that Instant Transfer Receive Root Directory is set to an existing directory path in the System Environment Settings.

E1013021: MSG=The Receive file name is invalid. FILEID=%s FILENAME=%s

Message Level:: E

Measure:: Check whether the pathname of the receive file exceeds the maximum length. If so, specify a shorter pathname. Also, check whether the pathname of the receive file contains a character other than alphanumeric characters. If so, specify a pathname containing only alphanumeric characters.

E1013022: MSG=Unable to transfer the file because Forced Strong Key mode is off on the remote host. Enabling Forced Strong Key mode is required on both side. FILEID=%s HOSTNAME=%s

Message Level:: E

Measure:

Check either of the following conditions are met:

The remote host runs HULFT lower than Ver.8.4.
The product of the remote host is a No Encryption.
Forced Strong Key mode on the remote host is off.

E1013024: MSG=Failed in the initialization of the Zstandard routine.

Message Level:: E

E1013025: MSG=Failed in the initialization of the Zstandard routine.

Message Level:: E

E1014001: MSG=Process fork error. STRERROR=%s

Message Level:: E

Measure:: Check the memory usage and the number of processes.

E1014002: MSG=hulrcvd end. SIGNUM=%d

Message Level:: E

E1014003: MSG=hulrcvd process received signal. PID=%d SIGNUM=%d

Message Level:: E

E1014004: MSG=hulrcvd process abnormal end. PID=%d

Message Level:: E

Measure:: Check log records in the Receive Log.

E1014005: MSG=Signal received in CSV processing. STS=%d FILEID=%s

Message Level:: E

E1014006: MSG=Signal received in job processing. STS=%d FILEID=%s JOBID=%s

Message Level:: E

E1015006: MSG=Socket read error. IPADDRESS=%s STRERROR=%s

Message Level:: E

Measure:: There may be problems in the socket stream. Check the environment. Also, check that it is not disconnected forcibly.

E1015010: MSG=Receive status file read error. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E1015011: MSG=Receive status file truncate error. STRERROR=%s

Message Level:: E

E1017001: MSG=Socket closed. FILEID=%s

Message Level:: E

E1018001: MSG=Verify version error. FILEID=%s HOSTNAME=%s

Message Level:: E

E1018002: MSG=Verify error. FILEID=%s HOSTNAME=%s

Message Level:: E

E1018003: MSG=Verify error. FILEID=%s HOSTNAME=%s

Message Level:: E

E1018004: MSG=Failed in the processing of the encryption exit routine. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E1018005: MSG=Failed to inflate the target file. FILEID=%s HOSTNAME=%s

Message Level:: E

E1018006: MSG=Unable to transfer the file because Forced Strong Key mode is off on the remote host. Enabling Forced Strong Key mode is required on both side. FILEID=%s HOSTNAME=%s

Message Level:: E

Measure:

Check either of the following conditions are met:

The remote host runs HULFT lower than Ver.8.4.
The product of the remote host is a No Encryption.
Forced Strong Key mode on the remote host is off.

E1019001: MSG=Receiving in XML format is unavailable.

Message Level:: E

E1021001: MSG=Failed to issue a request to DataSpider Servista. HTTPSTS=%d

Message Level:: E

Measure:: Check the HTTP status code and take measures.

E1021003: MSG=Failed to issue a request to DataSpider Servista.

Message Level:: E

Measure:: Check the settings of HULFT Script Port No.

E1021004: MSG=An error occurred while writing to the Receive Log file. HOSTNAME=%s FILEID=%s STS=%d DSTS=%d STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E1022001: MSG=Inconsistency is found between Forced Strong Key mode set in the System Environment Settings and the length of the cipher key specified in management information. FILEID=%s HOSTNAME=%s

Message Level:: E

Measure:

If Forced Strong Key mode is enabled, use a cipher key of 64 digits hexadecimal character string.

If Forced Strong Key mode is disabled, use a cipher key of 0 or 8 to 20 bytes alphanumeric character string.

I2001001: REQUEST=Exit daemon (from hulclusterobs) TYPE=force exit

Message Level:: I

I2001002: REQUEST=Exit daemon (from hulclusterobs) TYPE=term exit

Message Level:: I

I2001004: REPLY=Exit daemon (from hulclusterobs)

Message Level:: I

I2001005: REQUEST=Exit daemon (from hulclusterobs) TYPE=force exit

Message Level:: I

I2001006: MSG=hulobsd end.

Message Level:: I

I2002002: REQUEST=Exit daemon

Message Level:: I

I2002003: REPLY=Exit daemon

Message Level:: I

I2002004: MSG=hulobsd end.

Message Level:: I

I2003001: REQUEST=System environment query TYPE=Query All FILENAME=%s

Message Level:: I

I2003002: REQUEST=System environment query TYPE=Query enable set only FILENAME=%s

Message Level:: I

I2003004: REPLY=System environment query

Message Level:: I

I2004001: REQUEST=System environment resetting FILENAME=%s

Message Level:: I

I2004002: REPLY=System environment resetting

Message Level:: I

I2006014: MSG=Start to check file occupancy.

Message Level:: I

I2006016: MSG=Job execution process is started. TRGID=%s FILENAME=%s

Message Level:: I

I2006018: MSG=Job exec start. JOBID=%s EXECJOB=%s

Message Level:: I

I2006020: MSG=Job exec end. JOBID=%s EXECJOB=%s JOBSTS=%d

Message Level:: I

I2006024: MSG=Job execution process ended. TRGID=%s FILENAME=%s

Message Level:: I

I2006026: MSG=File trigger event was detected. EVENT=%s TRGID=%s FILENAME=%s

Message Level:: I

I2006036: REQUEST=Exit file trigger process

Message Level:: I

I2006037: REQUEST=Reload file trigger information

Message Level:: I

I2006039: REPLY=Exit file trigger process

Message Level:: I

I2006040: REPLY=Reload file trigger information CMDSTS=%d

Message Level:: I

I2006041: REPLY=Reload file trigger information (sync) CMDSTS=%d

Message Level:: I

I2006042: MSG=File trigger information does not exist. File trigger process stopped.

Message Level:: I

I2008001: REQUEST=Alive check

Message Level:: I

I2008002: REPLY=Alive check

Message Level:: I

I2008003: MSG=Service accepted. SERVICE=%s HOSTNAME=%s

Message Level:: I

I2008007: MSG=Service accepted. SERVICE=%s HOSTNAME=%s

Message Level:: I

I2008010: MSG=A request (%s) from an unregistered host has been accepted. The processing continues in accordance with the allowance/denial settings.

Message Level:: I

I2009005: MSG=hulobsd start (from hulclusterobs -endwait).

Message Level:: I

I2009006: MSG=hulobsd start (from hulclusterobs).

Message Level:: I

I2009007: MSG=hulobsd start.

Message Level:: I

I2010002: MSG=Service end. STS=%d DSTS=%d SERVICE=%s

Message Level:: I

I2011005: MSG=Job exec start. JOBID=%s EXECJOB=%s

Message Level:: I

I2011006: MSG=Job exec end. JOBID=%s EXECJOB=%s JOBSTS=%d

Message Level:: I

I2013002: MSG=The specified directory has been created successfully. PATH=%s

Message Level:: I

I2013004: MSG=The specified directory has been deleted successfully. PATH=%s

Message Level:: I

I2013006: MSG=The specified file has been deleted successfully. FILENAME=%s

Message Level:: I

W2006015: MSG=Cannot check file occupancy. The job is not executed. TRGID=%s FILENAME=%s

Message Level:: W

W2006017: MSG=Job information is not found. JOBID=%s

Message Level:: W

Measure:: Check that the relevant record is registered in the Job Information.

W2006021: MSG=Job exec end. JOBID=%s EXECJOB=%s JOBSTS=%d

Message Level:: W

W2006025: MSG=It does not agree to the monitor condition. The job is not executed. TRGID=%s FILENAME=%s

Message Level:: W

W2006027: MSG=Job execution has not ended. Job execution is skipped. TRGID=%s FILENAME=%s

Message Level:: W

W2006031: MSG=File status process still active. TRGID=%s

Message Level:: W

W2009008: MSG=File trigger process is not executed (HULTRG not exist).

Message Level:: W

W2011007: MSG=Job exec end. JOBID=%s EXECJOB=%s JOBSTS=%d

Message Level:: W

W2011008: MSG=Observe Definition file data error.

Message Level:: W

Measure:: Check that the Observe Definition file (service.db) is configured correctly.

W2011010: MSG=Job exec force end.

Message Level:: W

E2001003: MSG=Unknown protocol.

Message Level:: E

Measure:: An error occurred while receiving the data, or incorrect data might have been received. Transfer the data again.

E2002001: MSG=Socket read error. IPADDRESS=%s STRERROR=%s

Message Level:: E

Measure:: There may be problems in the socket stream. Check the environment. Also, check that it is not disconnected forcibly.

E2003003: REPLY=System environment query CMDSTS=%d

Message Level:: E

E2004003: REPLY=System environment resetting CMDSTS=%d

Message Level:: E

E2005001: MSG=Process fork error. STRERROR=%s

Message Level:: E

Measure:: Check the memory usage and the number of processes.

E2006001: MSG=Failed to allocate file list. STRERROR=%s

Message Level:: E

Measure:: Check the environment. Terminate any unnecessary applications when the memory is insufficient.

E2006002: MSG=Failed to allocate the top of file list. STRERROR=%s

Message Level:: E

Measure:: Check the environment. Terminate any unnecessary applications when the memory is insufficient.

E2006005: MSG=Failed to get the state of file to be monitored. TRGID=%s FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Failed to acquire the status of the file to be monitored. Check the error code returned from the operating system, and take measures.

E2006006: MSG=Name of the file to be monitored is too long. TRGID=%s FILENAME=%s

Message Level:: E

Measure:: Specify the name of the file to be monitored within 200 bytes.

E2006007: MSG=Failed to read the File Trigger Control file. STRERROR=%s

Message Level:: E

Measure:: Failed to read the File Trigger Control file (TriggerID.trgcntl.dat). Check the error code returned from the operating system and take measures.

E2006008: MSG=Cannot lock the File Trigger Control file. STRERROR=%s

Message Level:: E

Measure:: Failed to lock the File Trigger Control file (TriggerID.trgcntl.dat). Check the error code returned from the operating system and take measures.

E2006009: MSG=Failed to write the File Trigger Control file. STRERROR=%s

Message Level:: E

Measure:: Failed to write to the File Trigger Control file (TriggerID.trgcntl.dat). Check the error code returned from the operating system and take measures.

E2006010: MSG=Failed to allocate the top of trigger list. STRERROR=%s

Message Level:: E

Measure:: Check the environment. Terminate any unnecessary applications when the memory is insufficient.

E2006011: MSG=Failed to open the File Trigger Control file. STRERROR=%s

Message Level:: E

Measure:: Failed to open the File Trigger Control file (TriggerID.trgcntl.dat). Check the error code returned from the operating system and take measures.

E2006012: MSG=Failed to write the File Trigger Control file. STRERROR=%s

Message Level:: E

Measure:: Failed to write to the File Trigger Control file (TriggerID.trgcntl.dat). Check the error code returned from the operating system and take measures.

E2006013: MSG=Failed to reget the state of the file to be monitored. TRGID=%s FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Failed to acquire the status of the file to be monitored. Check the error code returned from the operating system and take measures.

E2006019: MSG=Cannot fork job execute process. STRERROR=%s

Message Level:: E

Measure:: Failed to create the child process. Check the error code returned from the operating system and take measures.

E2006022: MSG=Job execution process timed out. TRGID=%s FILENAME=%s

Message Level:: E

E2006023: MSG=Job execution process ended. TRGID=%s FILENAME=%s

Message Level:: E

E2006028: MSG=Starting job execution process failure. TRGID=%s FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Failed to create the child process. Check the error code returned from the operating system and take measures.

E2006029: MSG=Failed to allocate new file list. STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E2006030: MSG=Failed to write the File Trigger Control file. STRERROR=%s

Message Level:: E

Measure:: Failed to write to the File Trigger Control file (TriggerID.trgcntl.dat). Check the error code returned from the operating system and take measures.

E2006032: MSG=Cannot get state of file status process. TRGID=%s STRERROR=%s

Message Level:: E

Measure:: Failed to acquire the status of the child process. Check the error code returned from the operating system and take measures.

E2006033: MSG=File status process received signal. TRGID=%s SIGNUM=%d

Message Level:: E

E2006034: MSG=File status process abnormal end. TRGID=%s EXITCODE=%d

Message Level:: E

Measure:: Check the exit code and take measures.

E2006035: MSG=Cannot fork file status process. TRGID=%s STRERROR=%s

Message Level:: E

Measure:: Failed to create the child process. Check the error code returned from the operating system and take measures.

E2006038: MSG=File trigger process ended due to abnormal end of hulobsd.

Message Level:: E

E2006043: MSG=File trigger initialize error. STRERROR=%s

Message Level:: E

Measure:: Initialization of the File Trigger process failed. Check the error code returned from the operating system and take measures.

E2006044: MSG=Cannot get output file name. STRERROR=%s

Message Level:: E

Measure:: Check that the Observe Definition file (service.db) is configured correctly. Check the error code returned from the operating system and take measures.

E2006045: MSG=Cannot create a lock pipe (for file trigger process). STRERROR=%s

Message Level:: E

E2006046: MSG=Cannot create a request pipe (for file trigger process). STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E2006047: MSG=Cannot create an answer pipe (for file trigger process). STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E2006048: MSG=Cannot create a sync answer pipe (for file trigger process). STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E2006049: MSG=Cannot specify HULPATH that is longer than 200 bytes (File Trigger). LENGTH=%d

Message Level:: E

E2006050: MSG=Failed to open the File Trigger Control file. STRERROR=%s

Message Level:: E

Measure:: Failed to open the File Trigger Control file (TriggerID.trgcntl.dat). Check the error code returned from the operating system and take measures.

E2006051: MSG=Error occurred when matching filename with regular expression. TRGID=%s(%s)

Message Level:: E

Measure:: Check the setting of File Name (FILENAME) in the File Trigger Information.

E2006052: MSG=Failed to open the directory. FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E2006053: MSG=Failed to allocate file list. STRERROR=%s

Message Level:: E

Measure:: Check the environment. Terminate any unnecessary applications when the memory is insufficient.

E2007001: MSG=hulobsd end. SIGNUM=%d

Message Level:: E

E2007002: MSG=File trigger process end. SIGNUM=%d

Message Level:: E

E2007003: MSG=hulobsd process received signal. PID=%d SIGNUM=%d

Message Level:: E

E2007004: MSG=hulobsd process abnormal end. PID=%d

Message Level:: E

Measure:: Check log records in the Observe Log.

E2007005: MSG=hulobsd process end. SIGNUM=%d

Message Level:: E

E2007006: MSG=hulobsd ended due to abnormal end of file trigger process. STS=%d

Message Level:: E

E2008004: MSG=Memory allocate error. STRERROR=%s

Message Level:: E

Measure:: Check the environment. Terminate any unnecessary applications when the memory is insufficient.

E2008005: MSG=Received data is broken.

Message Level:: E

E2008006: MSG=Memory allocate error. STRERROR=%s

Message Level:: E

Measure:: Check the environment. Terminate any unnecessary applications when the memory is insufficient.

E2008008: MSG=Host Information file open error.

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E2008009: MSG=Host information is not found. HOSTNAME=%s

Message Level:: E

Measure:: Check that the host that issued the request is registered in the Host Information.

E2008011: MSG=The connection is refused because Forced Strong Key mode is off on the remote host. Enabling Forced Strong Key mode is required on both side. IPADDRESS=%s

Message Level:: E

Measure:

Check either of the following conditions are met:

The remote host runs HULFT lower than Ver.8.4.
The product of the remote host is a No Encryption.
Forced Strong Key mode on the remote host is off.

E2008012: MSG=The connection is refused because Forced Strong Key mode is off on the remote host. Enabling Forced Strong Key mode is required on both side. SERVICE=%s HOSTNAME=%s

Message Level:: E

Measure:

Check either of the following conditions are met:

The remote host runs HULFT lower than Ver.8.4.
The product of the remote host is a No Encryption.
Forced Strong Key mode on the remote host is off.

E2008013: MSG=The connection is refused because Forced Strong Key mode is off on the remote host. Enabling Forced Strong Key mode is required on both side. SERVICE=%s HOSTNAME=%s

Message Level:: E

Measure:

Check either of the following conditions are met:

The remote host runs HULFT lower than Ver.8.4.
The product of the remote host is a No Encryption.
Forced Strong Key mode on the remote host is off.

E2009001: MSG=Process fork error. STRERROR=%s

Message Level:: E

Measure:: Check the memory usage and the number of processes.

E2009009: MSG=Cannot initialize file trigger.

Message Level:: E

E2009010: MSG=File trigger process fork error. STRERROR=%s

Message Level:: E

Measure:: Failed to create the child process. Check the error code returned from the operating system and take measures.

E2010001: MSG=Service end. STS=%d DSTS=%d SERVICE=%s

Message Level:: E

E2010003: MSG=An error occurred while writing to the Observe Log file. HOSTNAME=%s SERVICE=%s STS=%d DSTS=%d STRERROR=%s

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E2011001: MSG=Job timeout. JOBID=%s

Message Level:: E

E2011002: MSG=Memory allocate error. JOBID=%s

Message Level:: E

E2011003: MSG=Job information is not found. JOBID=%s

Message Level:: E

Measure:: Check that the relevant record is registered in the Job Information.

E2011004: MSG=Process fork error. STRERROR=%s

Message Level:: E

Measure:: Check the memory usage and the number of processes.

E2011009: MSG=Process fork error. STRERROR=%s

Message Level:: E

Measure:: Check the memory usage and the number of processes.

E2012001: MSG=Send Management Information file open error.

Message Level:: E

Measure:: Check the error code returned from the operating system, and take measures.

E2012002: MSG=Send management information is not found. FILEID=%s

Message Level:: E

Measure:: Check that the relevant record is registered in the Send Management Information.

E2012003: MSG=Message replace error. FILEID=%s JOBID=%s

Message Level:: E

Measure:: Check the contents of the message and the field to be replaced. Check the length of the replaced message does not exceed the field length limit.

E2012004: MSG=Message replace error. FILEID=%s JOBID=%s

Message Level:: E

Measure:: Check the contents of the message and the field to be replaced. Check the length of the replaced message does not exceed the field length limit.

E2012005: MSG=Message replace error. FILEID=%s FILENAME=%s

Message Level:: E

Measure:: Check the contents of the message and the field to be replaced. Check the length of the replaced message does not exceed the field length limit.

E2012006: MSG=Message replace error. FILEID=%s FILENAME=%s

Message Level:: E

Measure:: Check the contents of the message and the field to be replaced. Check the length of the replaced message does not exceed the field length limit.

E2012007: MSG=Job information is not found. JOBID=%s

Message Level:: E

Measure:: Check that the relevant record is registered in the Job Information.

E2012008: MSG=Job timeout. FILEID=%s JOBID=%s

Message Level:: E

Measure:: Increase the setting of Job Timeout (jobwtimeout) in the System Environment Settings.

E2012009: MSG=Memory allocate error. STRERROR=%s

Message Level:: E

Measure:: Check the environment. Terminate any unnecessary applications when the memory is insufficient.

E2012010: MSG=Job exec end. JOBID=%s JOBSTS=%d

Message Level:: E

E2013001: MSG=Failed to create the specified directory. PATH=%s STRERROR=%s

Message Level:: E

Measure:: Check the specified directory.

E2013003: MSG=Failed to delete the specified directory. PATH=%s STRERROR=%s

Message Level:: E

Measure:: Check the specified directory.

E2013005: MSG=Failed to delete the specified file. FILENAME=%s STRERROR=%s

Message Level:: E

Measure:: Check the specified file.

Output message

Common Output Message

Output Message upon Sending

Output Message upon Receiving

Output Message upon the Request Acknowledge