Error codes for Send Management Information

END has not been entered in parameter file.

Enter END in the end of each management information.

The specified transfer type is incorrect.

Specify correct transfer type (FORMAT, BINARY, TEXT and MULTI.)

The specified compression preference is incorrect.

Specify a correct value for the compression preference. (N, 1, 2, or 3)

The transfer priority is incorrect.

Specify correct transfer priority. (1-256)

The transfer interval is incorrect.

Specify correct transfer interval. (0-32767)

The transfer block length is incorrect.

Specify correct transfer block length. (128-65520)

The Transfer Block Count is incorrect.

Specify correct transfer block count. (1-99)

The send file name has not been specified.

Enter send file name.

The transfer type has not been specified.

Enter transfer type.

The compression preference has not been specified.

Enter the compression preference.

The transfer group ID is not specified.

Enter transfer group ID.

The send file name exceeds the maximum length of 33 bytes.

Enter the send file name within 33 bytes.

The transfer group ID exceeds the maximum length of 50 bytes.

Shorten the transfer group ID to 50 bytes or less.

The successful job ID exceeds the maximum length of 50 bytes.

Shorten the successful job ID to 50 bytes or less.

The format ID exceeds the maximum length of 50 bytes.

Shorten the format ID to 50 bytes or less.

The Comment exceeds 60 bytes.

Enter the comment in less than 60 characters.

The multiplication of transfer block length and transfer block count exceeds 65,520 bytes.

Adjust transfer block length and transfer block count so that their product is 65,520 or less.

Specified tag name is incorrect.

Enter the correct tag name.

The format ID is not specified although the transfer type is format transfer, or the multi format ID is not specified although the transfer type is multi format transfer.

Change the transfer type or enter format ID or multi format ID.

Interface DBID is specified although the transfer type is other than format transfer.

Change the format type to format transfer or delete the value of Interface DBID.

The EBCDIC Code Set is incorrect.

Specify correct code set. (0, A-I, V-X)

A format ID is specified although the transfer type is not format transfer, or a multi format ID is specified although the transfer type is not multi format transfer.

Change the transfer type to format transfer or multi format transfer, or delete format ID or multi format ID.

The unsuccessful job ID exceeds the maximum length of 50 bytes.

Shorten the unsuccessful job ID to 50 bytes or less.

The EBCDIC code set has not been specified.

Enter the EBCDIC code set.

The send file mode is wrong.

Enter a valid send file mode (K, C, D, or L).

The file ID exceeds the maximum length of 50 bytes.

Shorten the file ID to 50 bytes or less.

File ID has not been specified.

Enter the file ID.

Specified code conversion is incorrect.

Specify a correct value for code conversion (S, R, or N).

The cipher key is too long or too short.

If Forced Strong Key mode is enabled, set 64 digits hexadecimal character strings as the cipher key.
If Forced Strong Key mode is disabled, omit the cipher key, or set 8 to 20 bytes of alphanumeric character.

Transfer using ciphers is not available.

HULFT Cipher Option has not been installed. Do not specify the Cipher Key.

The specification of the name of Send file is incorrect.

Confirm the specification of the name of the file, which is to be sent.

The pre-send job ID exceeds the maximum length of 50 bytes.

Shorten the pre-send job ID to 50 bytes or less.

The Shiftcode Mode is incorrect.

Enter a valid shiftcode mode (C, S).

The subsequent character cut is incorrect.

Specify a valid value for Subsequent Character (S or N).

The specified transfer type is invalid for specifying an archive file.

Specify "B" for the transfer type when you specify an archive file.

The comment contains a single quotation.

Remove single quotation from the comment.

The combination between the compression preference and the DEFLATE level is incorrect.

Determine to change Compression Preference to "DEFLATE" or not to specify the DEFLATE level based on the compression preference to use.

The specified DEFLATE level is incorrect.

Specify correct DEFLATE level. (S, D, C)

You can specify only a string "CSV" for the Interface DBID.

Do not specify Interface DBID, or specify "CSV" for Interface DBID.

The file ID is incorrect.

Enter the file ID in alphanumeric characters (and "_" if desired) within 50 bytes, which begin with an alphabetic character.

The Multi/Format ID is incorrect.

Enter the Multi/Format ID in alphanumeric characters (and "_" if desired) within 50 bytes, which begin with an alphabetic character.

The transfer group ID is incorrect.

Enter the transfer group ID in alphanumeric characters (and "_" if desired) within 50 bytes, which begin with an alphabetic character.

Pre-send job ID is incorrect.

Enter the pre-send job ID in alphanumeric characters (and "_" if desired) within 50 bytes, which begin with an alphabetic character.

Successful job ID is incorrect.

Enter the successful job ID in alphanumeric characters (and "_" if desired) within 50 bytes, which begin with an alphabetic character.

Unsuccessful job ID is incorrect.

Enter the unsuccessful job ID in alphanumeric characters (and "_" if desired) within 50 bytes, which begin with an alphabetic character.

Cipher Key (PASSWORD) is specified but invalid.

If Forced Strong Key mode is enabled, specify a character string of 64 bytes, consisting of from "0" through "9" and from "A" through "F", to Cipher Key (PASSWORD).